3D 打印的爱因斯坦-西拉德冰箱:用火来制冷3D Printed Einstein-Szilard Refrigerator Cools with Fire


AI free token/AI免费积分
3D 打印的爱因斯坦-西拉德冰箱:用火来制冷

它们未必效率最高,但凭借若干独特优势,吸收式冰箱在露营车和工业设施中始终占有一席之地:仅靠余热即可运行,而且由于几乎没有运动部件而显得相当可靠。不过,其工作原理有些晦涩,正因如此[Ben Krasnow]制作了一台透明的Einstein-Szilard冰箱。

多数吸收式冰箱以氨和水为工质;由于氨气需在室温下冷凝,系统压力会超过玻璃或塑料壳体所能轻松承受的范围。相比之下,Einstein-Szilard方案引入第三种液体作为制冷剂。通过加热沸腾,浓氨水溶液被分离,氨气通过降低制冷剂的分压促使其蒸发。随后,制冷剂蒸汽与氨气一同进入水中,氨溶于水,使制冷剂蒸汽得以冷凝并再次开启循环。重新形成的水-氨溶液回流至锅炉。

常规制冷剂多为丁烷,但由于[Ben]以明火为该加压系统提供热源,他改用不可燃的perfluoropentane。冰箱本体采用透明树脂3D打印,一块铜块将火焰热量传导至蒸发腔;氨溶液会腐蚀铜,故此举不具长期可靠性,但用于演示足矣。整机内部流道单一,带来一定难题:系统各区间几乎无压差,一旦气泡位置不当便易产生气阻。最终,[Ben]成功将其调试至比环境温度低五摄氏度。他还顺带提到,只要酒精浓度足够高,便可通过燃烧部分酒液来冰镇饮品。

对多数创客而言,氨制冷冰箱制作难度较大,但我们此前也见过以盐水为工质的吸收式冰箱。欲了解更多冷门冰箱,请查阅我们关于奇特制冷方式的文章。

感谢[spacedog]提供线索!

本文来源:https://hackaday.com/2026/10/31/3d-printed-einstein-szilard-refrigerator-cools-with-fire/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

They may not deliver the highest efficiency, but absorption refrigerators have earned a persistent place in camper vans and industrial plants thanks to a few distinct advantages: they can operate using waste heat alone as an energy source, and they can be quite reliable due to their lack of moving parts. It can be a bit hard to understand their working principles, though, which is why [Ben Krasnow] built a transparent Einstein-Szilard refrigerator .

Most absorption refrigerators use ammonia and water as their working fluids; since the ammonia gas needs to condense at room temperature, the refrigerator requires pressures above what can be comfortably held in a glass or plastic enclosure. The Einstein-Szilard design, by contrast, uses a third liquid as its refrigerant. A strong solution of ammonia in water is separated by boiling, and the ammonia gas induces the refrigerant to evaporate by decreasing its partial pressure. The refrigerant and ammonia gasses then mix with water, in which the ammonia dissolves, leaving the refrigerant vapor to condense and start the cycle again. The newly reformed water-ammonia solution flows back into the boiler.

The refrigerant is usually butane, but since [Ben] was powering this pressurized system with an open flame, he opted instead for nonflammable perfluoropentane. The refrigerator body itself was 3D printed in clear resin, with a copper block transferring heat from the flame to the boiler chamber; ammonia solutions do dissolve copper, so this isn’t a long-term solution, but it works for a demonstration. The single internal path of the refrigerator presented some difficulties: since almost no pressure builds up between different parts of the system, a bubble in the wrong place can easily airlock it. In the end, [Ben] managed to get it working well enough to reach five degrees Celsius below the ambient temperature. Conveniently, he notes that, for alcohol at a sufficiently high concentration, you could cool your drink by burning a portion of it.

3D Printed Einstein-Szilard Refrigerator Cools with Fire

Ammonia-based refrigerators are a tough build for most hackers, but we have seen a salt-water-based absorption refrigerator before. For more less-known refrigerators, check out our article on strange cooling methods .

暂无评论,快来发表第一条评论吧!No comments yet. Be the first!

📮 需求咨询📮 Inquiry