
总部位于广州的HackerGadgets推出了一款四合一Raspberry Pi HAT,集RTL-SDR和LoRa连接、GPS及北斗/GLONASS全球导航卫星系统(GNSS),以及PCF85063A实时时钟(RTC)于一体。
SDR部分通过RTL2832U+R860组合实现,支持100 kHz至1.74 GHz的频率范围以及100 kHz-28.8 MHz的高频(HF)直接采样。该HAT还配备Semtech SX1262 LoRa收发器,支持860-960 MHz频段、22 dBm最大输出功率,并支持Meshtastic固件。用户可根据计划使用的天线类型选择U.FL或SMA版本。
兼容性 Raspberry Pi 3B、4B和5——可直接安装。Raspberry Pi Zero和Zero 2 W——若板子带有40针排针则可直接安装;需检查整体高度和供电能力。
Raspberry Pi Zero和Zero 2 W——若板子带有40针排针则可直接安装;需检查整体高度和供电能力。
软件定义无线电(SDR)模块 芯片——Realtek RTL2832U + Rafael Micro R860,与许多RTL-SDR USB加密狗中所用相同 频率范围——100 kHz – 1.74 GHz 高频直接采样——100 kHz – 28.8 MHz 偏置三通(Bias Tee)——5V(软件控制) 振荡器——TCXO,近零漂移 状态指示器——侧面LED(偏置三通状态)
芯片——Realtek RTL2832U + Rafael Micro R860,与许多RTL-SDR USB加密狗中所用相同
LoRa模块 射频收发器——Semtech SX1262 频段——860 – 960 MHz 最大输出功率——22 dBm 振荡器——TCXO,近零漂移 开箱即用支持Meshtastic
(未命名)GNSS模块 卫星系统——根据DIP开关设置选择GPS + 北斗或GPS + GLONASS 支持PPS 支持有源或无源天线
卫星系统——根据DIP开关设置选择GPS + 北斗或GPS + GLONASS
RTC NXP PCF85063A RTC芯片 可充电3V纽扣电池 在Raspberry Pi断电时仍可持续、精准地计时
在Raspberry Pi断电时仍可持续、精准地计时
主机接口 RTL-SDR用USB——可使用USB Type-C端口或内部USB连接器,二者共用相同的针脚 40针Raspberry Pi GPIO排针——LoRa用SPI,GNSS用UART,RTC用I2C
RTL-SDR用USB——可使用USB Type-C端口或内部USB连接器,二者共用相同的针脚
40针Raspberry Pi GPIO排针——LoRa用SPI,GNSS用UART,RTC用I2C
其他——6位DIP开关,用于GNSS和RTC配置(详见下方PCB底面图示)
电源 通过GPIO排针供电5V Pi 5推荐5V/5A,Pi 4推荐5V/3A
连接至Raspberry Pi 5的SMA版本俯视图
要安装该HAT,需将其插入Raspberry Pi的GPIO排针,用螺丝固定,连接三根天线,最后将“内部USB线缆”接到Raspberry Pi的其中一个USB端口。你还可以根据需要调整DIP配置开关。
在软件方面,该公司推荐使用64位Raspberry Pi OS,以获得与RTL-SDR和Meshtastic用户空间工具的最佳兼容性。你还需要修改/boot/firmware/config.txt文件以启用I2C、SPI和UART,并修改/boot/firmware/cmdline.txt文件以移除串口控制台条目。文档中对此都有说明,你还可从中了解如何设置RTC、GNSS模块、RTL-SDR模块和Meshtastic。
该HAT的目标应用包括:使用SDR++或GQRX进行频谱分析以实时扫描无线电频谱并解码ADS-B、NOAA气象卫星信号;Meshtastic离网网状网络;无人机与车辆追踪;利用LoRa连接的物联网传感节点;RTC和GPS数据记录;用于气象气球探空仪的高频信号解码;业余无线电等等。
我们过去曾介绍过至少一款Raspberry Pi SDR HAT:CaribouLite RPi HAT。虽然它并非从100 kHz起步,但提供了更宽的30 MHz – 6 GHz频率范围,并且可在大多数Raspberry Pi单板计算机上工作,但Raspberry Pi 5除外,因为它缺少所需的SMI接口。用于接入追踪的LoRa + GPS HAT已经问世有一段时间了,我们在2016年报道过Dragino LoRa/GPS HAT,2019年报道过Docker Pi IoT Node(A)。较新的方案是RAKwireless WisMesh Pi HAT RAK6421,你可以为其添加LoRa和GPS模块。RAK不提供SDR模块,因此除非使用RTL-SDR USB加密狗,否则无法轻易复现这款四合一HackerGadgets HAT板,这使得它成为一个相当独特的方案。
HackerGadgets出售这款RTL-SDR/LoRa/GPS/RTC HAT,不含天线售价84.90美元,含三根U.FL或SMA天线售价108.50美元。
本文来源:https://www.cnx-software.com/2026/11/22/4-in-1-raspberry-pi-hat-combines-rtl-sdr-lora-gps-and-rtc/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

Guangzhou-based HackerGadgets has launched a 4-in-1 Raspberry Pi HAT that offers RTL-SDR and LoRa connectivity, GPS and Beidou/GLONASS GNSS, and a PCF85063A real-time clock (RTC).
The SDR part is implemented through an RTL2832U+R860 combo supporting 100 kHz to 1.74 GHz frequency and 100 kHz-28.8 MHz HF direct sampling. The HAT also features a Semtech SX1262 LoRa transceiver supporting the 860-960 MHz frequency band, 22 dBm max output power, and Meshtastic firmware. Users can select between U.FL and SMA versions depending on the type of antennas they plan to use.
Compatibility Raspberry Pi 3B, 4B, and 5 – Direct installation. Raspberry Pi Zero and Zero 2 W – Direct installation if the board has a 40-pin header; check overall height and power capacity.
Raspberry Pi Zero and Zero 2 W – Direct installation if the board has a 40-pin header; check overall height and power capacity.
Software-defined radio (SDR) module Chips – Realtek RTL2832U + Rafael Micro R860 as used in many RTL-SDR USB dongles Frequency Range – 100 kHz – 1.74 GHz HF Direct Sampling – 100 kHz – 28.8 MHz Bias Te – e5V (software-controlled) Oscillator – TCXO, near-zero drift Status Indicator – Side LED (Bias Tee status)
Chips – Realtek RTL2832U + Rafael Micro R860 as used in many RTL-SDR USB dongles
LoRa module RF transceiver – Semtech SX1262 Frequency Band – 860 – 960 MHz Max Output Power – 22 dBm Oscillator – TCXO, near-zero drift Meshtastic support out of the box
(Unnamed) GNSS module Satellite systems – GPS + Beidou or GPS + GLONASS depending on DIP switch settings PPS support Active or passive antenna support
Satellite systems – GPS + Beidou or GPS + GLONASS depending on DIP switch settings
RTC NXP PCF85063A RTC chip Rechargeable 3V coin cell battery Supports continuous, accurate timekeeping when the Raspberry Pi is powered off
Supports continuous, accurate timekeeping when the Raspberry Pi is powered off
Host interfaces USB for RTL-SDR – Either the USB Type-C port or the internal USB connector, which shares the same pins 40-pin Raspberry Pi GPIO header – SPI for LoRa, UART for GNSS, and I2C for RTC
USB for RTL-SDR – Either the USB Type-C port or the internal USB connector, which shares the same pins
40-pin Raspberry Pi GPIO header – SPI for LoRa, UART for GNSS, and I2C for RTC
Misc – 6-position DIP switch for GNSS and RTC configuration (See bottom side of PCB below for details)
Power Supply 5V via GPIO header 5V/5A recommended for Pi 5, 5V/3A for Pi 4
Top view of the SMA version connected to a Raspberry Pi 5
To install the HAT, you need to insert it into the Raspberry Pi GPIO header, secure it with screws, connect the three antennas, and finally connect the “internal USB cable” to one of the Raspberry Pi USB ports. Optionally, you can adjust the DIP configuration switch to meet your requirements.
On the software side, the company recommends Raspberry Pi OS 64-bit for best compatibility with RTL-SDR and Meshtastic user-space tools. You’ll also need to modify the /boot/firmware/config.txt file to enable I2C, SPI, and UART, and the /boot/firmware/cmdline.txt file to remove the serial console entry. This is all explained in the documentation , where you’ll also find out how to set up the RTC, the GNSS module, the RTL-SDK module, and Meshtastic.
Target applications for the HAT include spectrum analysis using SDR++ or GQRX to scan the radio spectrum in real time and decode ADS-B, NOAA weather satellite signals, Meshtastic off-grid mesh networking, drone & vehicle tracking , IoT sensor node using LoRa connectivity, RTC and GPS data logging , HF signal decoding for weather balloon radiosondes, amateur radio, and more.
We’ve noted at least one Raspberry Pi SDR HAT in the past: the CaribouLite RPi HAT . While it doesn’t start at 100 kHz, it offers a wider 30 MHz – 6 GHz frequency range, and works on most Raspberry Pi SBCs, except the Raspberry Pi 5, which lacks the required SMI interface. LoRa + GPS HATs for access tracking have been around for a while, and we covered the Dragino LoRa/GPS HAT in 2016 and the Docker Pi IoT Node(A) in 2019. A more recent solution is the RAKwireless WisMesh Pi HAT RAK6421 , to which you can add LoRa and GPS modules. RAK does not offer an SDR module, so there’s no way to easily reproduce the 4-in-1 HackerGadgets HAT board, unless using an RTL-SDR USB dongle, and it’s quite a unique solution.
HackerGadgets sells the RTL-SDR/LoRa/GPS/RTC HAT for $84.90 without antennas or $108.50 with the three U.FL or SMA antennas .
本文来源:https://www.cnx-software.com/2026/11/22/4-in-1-raspberry-pi-hat-combines-rtl-sdr-lora-gps-and-rtc/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。