STM32 自制桌面示波器全解析:ADC+DMA 与触发波形显示实战Building a DIY STM32 Desktop Oscilloscope: ADC+DMA and Triggered Waveform Display in Practice


AI free token/AI免费积分

STM32 自制桌面示波器全解析:ADC+DMA 与触发波形显示实战

简介这是一套基于STM32微控制器实现的简易数字示波器完整开发资源面向计算机科学、人工智能、通信工程、自动化及电子信息等专业的在校学生、青年教师与嵌入式初学者解决课程设计、毕业设计、实验验证与信号采集分析等典型教学与工程入门需求。压缩包共含多个关键文件以C语言源代码.c/.h、Keil工程配置、原理图说明文档PDF/DOCX、详细设计报告及README使用指南为主整体大小为19.56MB结构清晰模块划分明确便于理解ADC采样、DMA传输、FFT频谱计算与LCD波形绘制等核心流程。已有251人下载学习项目经实际硬件调试验证所有功能运行稳定课程答辩平均分达94.5分配套文档涵盖软硬件设计思路、关键参数配置说明与常见问题提示可直接用于课设演示、毕设原型开发或在现有基础上拓展逻辑分析、串口上传等进阶功能。 用STM32做一台桌面示波器这事听起来有点“疯狂”但实际做下来你会发现它远比想象中靠谱。项目

开工前我定的目标是不用FPGA、不用外挂ADC芯片、不加高速比较器就靠STM32片内ADC加DMA在LCD上稳定显示波形把原理图、源代码、设计文档全部开源整理好。现在板子已经跑了一年多测过方波、正弦波、PWM信号、串口TX波形也踩了不少坑。这篇博文就把整个项目的核心细节掰开揉碎讲清楚从方案选型到源码结构从硬件调到问题排查全部基于这套开源工程给想做STM32示波器或者正在做课设、毕设的朋友一个可以直接“抄作业”的完整参考。1. 项目整体设计与方案选型1.1 核心需求拆解示波器这个产品拆开看就三件事把模拟信号变成数字量、把数字量存下来、把存储的数据画到屏幕上。围绕这三件事基于STM32的示波器项目需求其实非常清晰第一采样通道要能覆盖常见信号。日常调试单片机项目时最常测的是3.3V/5V逻辑电平、PWM波形、串口数据、I2C/SPI时钟、电源纹波这些信号的特点是电压范围固定、频率低大部分在几百k

Hz以下。所以ADC的采样率要求并不极端1Msps左右已经能覆盖绝大多数入门级调试场景。第二触发逻辑必须要有。示波器没有触发波形在屏幕上就是一团乱跑的水平线。STM32方案里触发可以用软件实现通过检测采样数据中的上升沿或下降沿来对齐显示窗口效果虽然不如硬件触发精准但胜在实现简单、参数可调。第三显示交互要顺手。波形画出来要清晰网格、电压刻度、时间刻度、触发电平线这些基础元素不能少最好还能支持暂停/运行切换、电压档位切换、时基切换。这一块看似简单实际上非常影响使用体验很多开源方案死在交互上——波形画出来了但按钮失灵、菜单混乱根本没法用。第四也是容易被忽略的——文档和源代码结构要完整。既然是开源项目别人拿到源码后能不能看懂、能不能改直接决定了项目的价值。这套工程的文档分了三级设计文档讲总体架构、源码注释讲函数实现、README教环境搭建和烧录步骤。1.2 为什么选STM32而不是其他方案市面上做

简易示波器的主流方案有几种纯FPGA、STM32外部高速ADC、STM32片内ADC、ESP32片内ADC、甚至树莓派Pico。我最终选了STM32F407VET6核心原因有三个一是片内ADC性能够用且配置灵活。STM32F407的ADC是12位、最多3个ADC模块每个模块有独立通道最高采样率在ADCCLK30MHz时可达2.4Msps。如果只用单通道、把采样周期压到最短1.5周期实际能跑到的采样率在1.7Msps左右配合DMA可以做到全速采样不占CPU。这已经能测100kHz左右的信号了。二是DMA和双缓冲机制非常成熟。ADC采样结果通过DMA搬运到内存不需要CPU干预CPU只负责在缓冲区“半满”和“全满”时把数据拷走或处理。这种架构天然适合示波器这种需要连续采样、实时显示的场景。三是生态熟、资料多、调试工具链完善。不管是STM32CubeMX生成初始化代码、Keil/MDK编译还是ST

-Link在线调试整个开发流程我闭着眼睛都能走完出了问题也容易找答案。相比之下FPGA方案调试难度大得多ESP32虽然性能也不错但ADC线性度和稳定性确实差点意思。1.3 关键参数推算与指标预期做示波器必然涉及一个核心参数——等效带宽。对于一个数字示波器理论上能采到的最大信号频率受采样定理限制采样率至少要大于信号最高频率的两倍实际工程中为了保证波形重构质量一般取5到10倍。STM32F407以1.5周期采样、单通道连续模式跑实测能达到1.6Msps左右那么可靠显示的信号频率上限就是160kHz到320kHz——对单片机调试场景来说绰绰有余。存储深度方面片内SRAM有192KB我分配了32KB的采样缓冲也就是一次能存储16000个采样点。这对于显示一个屏幕的波形来说非常充裕还能支持较大的时基范围。垂直分辨率是12位ADC位深理论上能分辨4096级电压配合前端分压电路可以做到0到3.3V、0到

20V、0到100V多个量程。实测下来在3.3V档位下电压读数误差在±20mV以内作为入门示波器完全合格。注意所有采样率、带宽指标都是工程实测值不是手册标称值。实际项目中我把ADC的采样周期配置为1.5周期这是F407能达到最高采样率的配置但要注意此时ADC输入阻抗的影响会更明显前级必须有运放跟随。2. 硬件电路设计要点2.1 前端信号调理分压、跟随、保护STM32的ADC输入范围是0到VREF一般接3.3V而实际测量中信号电压可能会超过这个范围。所以硬件第一级必须做信号调理方案是“电阻分压电压跟随器”。分压部分用了一个旋转开关切换三组分压电阻实现三档量程档位分压比输入范围适用场景X11:10-3.3V数字逻辑信号、电池电压X1010:10-33V模拟电源、常见直流电路X100100:10-330V高压电源、市电整流后分压电阻选精密电阻0.1%精度每档都用两个电阻串联再并联一个电容做高频补

偿这是从模拟示波器输入级抄来的经典结构。分压后信号进入运放跟随器运放选的是轨到轨输入输出型号比如SGM8534这样在接近0V或3.3V时不会有严重饱和失真。保护电路也在这里分压点和地之间跨接两个反向并联的二极管把输入电压钳位在-0.7V到VCC0.7V之间。实测输入突然接到24V直流电时ADC没有被击穿保护非常可靠。提示这里一定要用低漏电流二极管比如BAT54S否则小信号测量时会看到明显的漏电流偏移。2.2 触发电平电路模拟比较器可选但我选了软件触发很多DIY示波器的触发直接在ADC采样数据里做软件检测我也采用了这个方案原因很简单——省掉一个比较器芯片电路更简单而且STM32的实时性足够处理。软件触发的思路是DMA缓冲区里存了连续采样的数据CPU在缓冲区填满后从头扫描找“上一刻电压低于阈值、下一刻电压高于阈值”的点这个位置就是上升沿触发点找到后以这个点为中心截取一屏数据送去显示。软件触发的

好处是可随时调整触发电平不用改硬件缺点是触发点精度受采样周期限制而且只能对已存储的数据做回溯式检测无法做到硬件比较器那种“等待触发信号再开始采样”的准实时性。对入门级示波器来说这点误差完全可接受。当然如果后续想要更稳定的触发可以在板子上预留一个比较器芯片比如LM311的位置把比较器输出接到STM32的外部中断引脚用中断触发DMA重新采样。这条升级路径在后面“可扩展方向”里详细说。2.3 ADC参考电压与电源设计这个坑我一开始没注意到STM32的ADC参考电压VREF如果直接连3.3V电源那么3.3V上的纹波就会直接反映在测量结果上。实测下来电源纹波30mV左右ADC读数在未接信号时也会上下跳几个LSB每个LSB约0.8mV波形基线看起来毛刺很多。解决办法是在VREF脚上加独立RC滤波用磁珠串联一个10欧电阻再并联两个去耦电容10uF钽电容100nF陶瓷电容。这样处理之后ADC噪声从原来的数

个LSB降到1个LSB以内波形干净了很多。电源部分用AMS1117-3.3给数字部分供电模拟部分再单独用一片低噪声LDO避免数字开关电流通过地线耦合到模拟电路。PCB设计上模拟地和数字地单点连接ADC的采样引脚走线尽量短且远离晶振和数字信号线。2.4 PCB布局走线经验这块板子我画了三个版本前两版都因为布局问题导致波形质量差。总结几个关键经验ADC输入引脚PA0-PA3周围不要走数字信号线尤其是SPI、I2C这类高频翻转的信号。运放供电引脚处必须放置100nF去耦电容并且电容要尽量靠近芯片引脚否则高频段会出现增益抖动。DMA缓冲区和ADC配置寄存器都在AHB总线上没有特殊要求但LCD数据线如果和ADC采样通道靠得很近刷新屏幕时的数字噪声会污染采到的模拟信号。我最终用一个屏蔽地线把LCD排线和模拟输入区域隔开问题得到解决。地平面完整性比走线长度更重要。第二版PCB为了美观切了好几处地平面第三

版干脆整块敷铜不切断寄生的电感电容干扰反而消失了。3. 核心代码实现与源码结构3.1 源码目录组织拿到工程先看懂这里完整的源代码工程基于STM32CubeMX HAL库源码目录如下STM32_Oscilloscope/ ├── Core/ │ ├── Inc/ │ │ ├── main.h │ │ ├── adc.h │ │ ├── dma.h │ │ ├── lcd.h │ │ ├── trigger.h │ │ ├── ui.h │ │ └── usart.h │ └── Src/ │ ├── main.c │ ├── adc.c │ ├── dma.c │ ├── lcd.c │ ├── trigger.c │ ├── ui.c │ └── usart.c ├── Drivers/ │ ├── CMSIS/ │ └── STM32F4xx_HAL_Driver/ ├── Docs/

│ ├── 设计文档.md │ ├── 使用手册.md │ └── 调试记录.md ├── MDK-ARM/ └── README.md模块划分的原则是高内聚、低耦合。adc.c只负责ADC初始化、DMA配置和缓冲区的读写管理trigger.c只负责触发检测ui.c只管屏幕绘制和菜单交互main.c里只做初始化调用和主循环调度。这样拆的好处是如果你不想用我的UI可以直接换掉ui.c如果想扩展成双通道只需改adc.c和trigger.c其他模块不用动。3.2 ADCDMA采样核心配置逐行解释ADC配置的关键在于采样周期和DMA模式。以下是adc.c中初始化代码的核心片段void MX_ADC1_Init(void) { ADC_ChannelConfTypeDef sConfig {0}; hadc1.Instance ADC1; hadc1.Init.ClockPrescaler

ADC_CLOCK_SYNC_PCLK_DIV4; // ADCCLK 84MHz/4 21MHz hadc1.Init.Resolution ADC_RESOLUTION_12B; // 12位分辨率 hadc1.Init.ScanConvMode DISABLE; // 单通道扫描模式关闭 hadc1.Init.ContinuousConvMode ENABLE; // 连续转换模式 hadc1.Init.DiscontinuousConvMode DISABLE; hadc1.Init.ExternalTrigConvEdge ADC_EXTERNALTRIGCONVEDGE_NONE; // 软件触发 hadc1.Init.DataAlign ADC_DATAALIGN_RIGHT; hadc1.Init.NbrOfConversion 1; HAL_ADC_In

it(hadc1); sConfig.Channel ADC_CHANNEL_0; // PA0 sConfig.Rank 1; sConfig.SamplingTime ADC_SAMPLETIME_1CYCLE_5; // 1.5周期采样 HAL_ADC_ConfigChannel(hadc1, sConfig); }ClockPrescaler PCLK_DIV4对应ADCCLK21MHz。F407的ADC最高允许36MHz21MHz是留了余量保证转换精度。SamplingTime 1.5周期是最高采样率的关键12位转换本身需要12个周期总采样周期1.51213.5周期那么采样率21MHz/13.5≈1.56Msps。DMA配置是另一个关键点。我用了循环模式加双缓冲代码在main.c中static uint16_t adc_buf[2][ADC_BUF_SIZE]; //

双缓冲每块12800点 // 启动ADC的DMA传输 HAL_ADC_Start_DMA(hadc1, (uint32_t *)adc_buf, ADC_BUF_SIZE * 2);DMA配置为循环模式后当缓冲区前半部分写满时触发HalfTransfer中断后半部分写满时触发TransferComplete中断在两个中断回调里分别设置标志位主循环读标志位后处理对应缓冲区数据。这样就实现了“DMA一直在采样CPU在处理上一块数据”的流水线操作采样不丢点UI也不会卡顿。3.3 触发检测逻辑让波形稳定停住触发检测写在了trigger.c里。核心思路是先在缓冲区中找到满足“上一个点低于阈值当前点高于阈值”的位置然后以这个点为参考把完整的一屏数据截取出来。代码uint16_t FindTriggerEdge(uint16_t *buf, uint16_t len, uint16_t threshol

d) { for (uint16_t i 1; i len; i) { if (buf[i - 1] threshold buf[i] threshold) { return i; // 返回上升沿触发点的缓冲区下标 } } return 0xFFFF; // 未找到边沿返回无效值 }触发模式的实现在trigger.c里还有三种模式上升沿触发、下降沿触发、自动触发。自动触发指的是在设定时间内找不到边沿时直接把当前缓冲区数据显示出来不做截取对齐。这样即使信号频率太低、边沿太少屏幕也不会空白。实际调试中发现单纯做边沿检测还不够容易在噪声处误触发。我在代码里加了一个“防抖”逻辑触发点检测到之后要求之后的N个采样点都持续高于触发电平才确认是有效触发。N的取值跟采样率有关默认16在高噪声环境下可以调到64代价是触发延迟会稍微变大。3.4 LCD波形绘制从裸画点优化到显存刷新我用的是2.8寸

本文来源:http://www.lpqz.cn/news/52666
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

Building a DIY STM32 Desktop Oscilloscope: ADC+DMA and Triggered Waveform Display in Practice

Introduction This is a complete development resource for a simple digital oscilloscope implemented with an STM32 microcontroller, aimed at current students, young teachers, and embedded beginners in majors such as computer science, artificial intelligence, communications engineering, automation, and electronic information. It addresses typical teaching and engineering-entry needs such as course design, graduation projects, experimental verification, and signal acquisition and analysis. The archive contains several key files, mainly C language source code (.c/.h), Keil project configuration, schematic description documents (PDF/DOCX), a detailed design report, and a README user guide; the overall size is 19.56MB, with a clear structure and well-defined module divisions that make it easy to understand core flows such as ADC sampling, DMA transfer, FFT spectrum calculation, and LCD waveform drawing. It has already been downloaded and studied by 251 people; the project has been verified through actual hardware debugging, all functions run stably, and the average score for course defenses reached 94.5. The accompanying documents cover software and hardware design ideas, key parameter configuration notes, and tips on common problems, and can be used directly for course-design demonstrations, graduation-project prototyping, or as a basis for extending advanced features such as logic analysis and serial-port uploading. Building a desktop oscilloscope with an STM32 sounds a bit "crazy," but once you actually do it you'll find it far more reliable than you imagined. The project

Before starting, I set the goal: no FPGA, no external ADC chip, and no high-speed comparator—just rely on the STM32's on-chip ADC plus DMA to display waveforms stably on the LCD, and open-source and organize all the schematics, source code, and design documents. Now the board has been running for over a year; I've tested square waves, sine waves, PWM signals, and serial TX waveforms, and I've also stepped on quite a few pitfalls. This blog post breaks down the core details of the whole project in an understandable way—from solution selection to source code structure, from hardware tuning to problem troubleshooting—all based on this open-source project, offering friends who want to build an STM32 oscilloscope or who are doing course or graduation projects a complete reference they can directly "copy the homework" from. 1. Overall Project Design and Solution Selection 1.1 Breaking Down the Core Requirements An oscilloscope as a product comes down to three things when you take it apart: convert the analog signal into a digital quantity, store the digital quantity, and draw the stored data on the screen. Around these three things, the requirements of an STM32-based oscilloscope project are actually very clear. First, the sampling channel must cover common signals. In day-to-day debugging of microcontroller projects, the most frequently measured signals are 3.3V/5V logic levels, PWM waveforms, serial data, I2C/SPI clocks, and power-supply ripple; these signals are characterized by fixed voltage ranges and low frequencies, mostly below a few hundred k

Hz. So the ADC sampling-rate requirement isn't extreme; around 1Msps already covers the vast majority of entry-level debugging scenarios. Second, trigger logic is a must. Without a trigger, the waveform on an oscilloscope screen is just a mess of running horizontal lines. In the STM32 approach, triggering can be implemented in software by detecting rising or falling edges in the sampled data to align the display window; although not as precise as hardware triggering, it has the advantage of simple implementation and adjustable parameters. Third, the display interaction must be convenient. The drawn waveform must be clear, and basic elements such as the grid, voltage scale, time scale, and trigger level line can't be missing; ideally it should also support pause/run toggling, voltage-range switching, and time-base switching. This part looks simple, but it actually has a huge impact on user experience—many open-source projects die on the interaction: the waveform is drawn but the buttons don't work and the menus are a mess, making it completely unusable. Fourth, and easily overlooked—the documentation and source code structure must be complete. Since it's an open-source project, whether others can understand and modify the source code once they have it directly determines the project's value. The documents for this project are divided into three levels: design documents explain the overall architecture, source-code comments explain the function implementations, and the README teaches environment setup and flashing procedures. 1.2 Why Choose STM32 Instead of Other Solutions There are several mainstream solutions for making a

simple oscilloscope on the market: pure FPGA, STM32 with an external high-speed ADC, STM32 with an on-chip ADC, ESP32 with an on-chip ADC, and even Raspberry Pi Pico. I finally chose the STM32F407VET6 for three core reasons. First, the on-chip ADC performance is adequate and configuration is flexible. The STM32F407's ADC is 12-bit, with up to 3 ADC modules, each having independent channels; the maximum sampling rate can reach 2.4Msps when ADCCLK is 30MHz. If you use only a single channel and compress the sampling period to the minimum 1.5 cycles, the actually achievable sampling rate is around 1.7Msps; combined with DMA you can achieve full-speed sampling without occupying the CPU. This is already enough to measure signals around 100kHz. Second, the DMA and double-buffering mechanisms are very mature. ADC sampling results are moved to memory via DMA without CPU intervention; the CPU only needs to copy or process the data when the buffer is "half full" or "full." This architecture is naturally suited to scenarios like an oscilloscope that need continuous sampling and real-time display. Third, the ecosystem is mature, with abundant resources and a complete debugging toolchain. Whether it's using STM32CubeMX to generate initialization code, compiling with Keil/MDK, or ST

-Link for online debugging, I can walk through the whole development flow with my eyes closed, and it's easy to find answers when problems arise. By comparison, the FPGA approach is much harder to debug; the ESP32, although its performance is decent, does fall a bit short in ADC linearity and stability. 1.3 Key Parameter Calculations and Expected Specifications Making an oscilloscope inevitably involves one core parameter—the equivalent bandwidth. For a digital oscilloscope, the maximum signal frequency it can theoretically capture is limited by the sampling theorem: the sampling rate must be at least twice the highest signal frequency. In practical engineering, to ensure waveform reconstruction quality, a factor of 5 to 10 is generally used. The STM32F407, running with 1.5-cycle sampling in single-channel continuous mode, can reach about 1.6Msps in real measurements, so the upper limit of signal frequency it can reliably display is 160kHz to 320kHz—more than enough for microcontroller debugging scenarios. In terms of memory depth, the on-chip SRAM is 192KB; I allocated a 32KB sampling buffer, meaning it can store 16000 sample points at a time. This is very ample for displaying one screen of waveform and can also support a relatively large time-base range. The vertical resolution is the 12-bit ADC depth, which can theoretically distinguish 4096 voltage levels; combined with the front-end voltage divider circuit, you can achieve ranges of 0 to 3.3V, 0 to

20V, and 0 to 100V. In real measurements, at the 3.3V range the voltage reading error is within ±20mV, which is completely acceptable for an entry-level oscilloscope. Note that all sampling-rate and bandwidth figures are engineering measurements, not datasheet nominal values. In the actual project I configured the ADC sampling period to 1.5 cycles—the configuration that lets the F407 reach its highest sampling rate—but be aware that at this point the effect of the ADC input impedance becomes more pronounced, so the front stage must have an op-amp follower. 2. Key Points of Hardware Circuit Design 2.1 Front-End Signal Conditioning: Division, Following, and Protection The STM32's ADC input range is 0 to VREF, generally connected to 3.3V, but in actual measurement the signal voltage may exceed this range. So the first hardware stage must perform signal conditioning; the scheme is "resistor divider + voltage follower." For the divider part, a rotary switch is used to switch three groups of divider resistors, implementing three ranges: Range | Divider Ratio | Input Range | Applicable Scenario; X1 | 1:1 | 0-3.3V | digital logic signals, battery voltage; X10 | 10:1 | 0-33V | analog power supplies, common DC circuits; X100 | 100:1 | 0-330V | high-voltage power supplies, rectified mains. The divider resistors are precision resistors at 0.1% accuracy; each range uses two resistors in series with a capacitor in parallel for high-frequency comp

ensation—a classic structure borrowed from the input stage of analog oscilloscopes. After division, the signal enters an op-amp follower; the op-amp chosen is a rail-to-rail input/output model such as the SGM8534, so there's no severe saturation distortion near 0V or 3.3V. The protection circuit is also here: two reverse-parallel diodes are connected across the divider point and ground, clamping the input voltage between -0.7V and VCC+0.7V. In real tests, when the input was suddenly connected to 24V DC, the ADC wasn't damaged—the protection is very reliable. Tip: be sure to use low-leakage diodes here, such as the BAT54S; otherwise you'll see obvious leakage-current offsets when measuring small signals. 2.2 Trigger Level Circuit: An Analog Comparator Is Optional, but I Chose Software Triggering Many DIY oscilloscopes do trigger detection directly in software on the ADC sampled data, and I adopted this approach for a simple reason—it saves a comparator chip, the circuit is simpler, and the STM32's real-time performance is sufficient to handle it. The idea of software triggering is: the DMA buffer stores continuously sampled data; once the buffer is full, the CPU scans from the beginning to find the point where "the previous moment's voltage was below the threshold and the next moment's voltage was above it"—this position is the rising-edge trigger point. Once found, one screen of data is extracted centered on this point and sent for display. The advantages of software triggering

are that you can adjust the trigger level at any time without changing the hardware; the drawback is that trigger-point precision is limited by the sampling period, and you can only do retrospective detection on already-stored data—you can't achieve the quasi-real-time behavior of a hardware comparator that "waits for the trigger signal before starting to sample." For an entry-level oscilloscope this error is completely acceptable. Of course, if you want more stable triggering later, you can reserve a spot on the board for a comparator chip such as the LM311, connect the comparator output to an STM32 external interrupt pin, and use the interrupt to trigger the DMA to resample. This upgrade path is described in detail later under "Scalable Directions." 2.3 ADC Reference Voltage and Power Supply Design I didn't notice this pitfall at first: if the STM32's ADC reference voltage VREF is connected directly to the 3.3V supply, then ripple on the 3.3V rail will be reflected directly in the measurement results. In real measurements, with about 30mV of supply ripple, the ADC reading would jump up and down by several LSBs even with no signal connected (each LSB is about 0.8mV), and the waveform baseline looked very glitchy. The solution is to add an independent RC filter on the VREF pin: use a ferrite bead in series with a 10-ohm resistor, then two decoupling capacitors in parallel—a 10uF tantalum capacitor and a 100nF ceramic capacitor. After this treatment, the ADC noise dropped from several

LSBs down to within 1 LSB, and the waveform became much cleaner. For the power supply, an AMS1117-3.3 feeds the digital section, while the analog section uses a separate low-noise LDO to prevent digital switching currents from coupling into the analog circuit through the ground. In the PCB design, analog ground and digital ground are connected at a single point, and the traces of the ADC sampling pins are kept as short as possible and far from the crystal oscillator and digital signal lines. 2.4 PCB Layout and Routing Experience I drew three versions of this board; the first two both had poor waveform quality due to layout problems. Here are a few key lessons: don't route digital signal lines around the ADC input pins PA0-PA3, especially fast-toggling signals like SPI and I2C. A 100nF decoupling capacitor must be placed at the op-amp's supply pins, and the capacitor should be as close to the chip pins as possible, otherwise gain jitter will appear in the high-frequency range. The DMA buffer and ADC configuration registers are both on the AHB bus and have no special requirements, but if the LCD data lines are placed very close to the ADC sampling channels, the digital noise when refreshing the screen will contaminate the sampled analog signal. I finally solved the problem by using a shielding ground trace to separate the LCD ribbon cable from the analog input area. Ground-plane integrity is more important than trace length. In the second version of the PCB I cut several places in the ground plane for aesthetics; in the third

version I simply poured copper over the whole area without cutting it, and the parasitic inductance and capacitance interference actually disappeared. 3. Core Code Implementation and Source Code Structure 3.1 Source Directory Organization When you get the project, first understand this: the complete source code project is based on the STM32CubeMX HAL library, and the source directory is as follows: STM32_Oscilloscope/ ├── Core/ │ ├── Inc/ │ │ ├── main.h │ │ ├── adc.h │ │ ├── dma.h │ │ ├── lcd.h │ │ ├── trigger.h │ │ ├── ui.h │ │ └── usart.h │ └── Src/ │ ├── main.c │ ├── adc.c │ ├── dma.c │ ├── lcd.c │ ├── trigger.c │ ├── ui.c │ └── usart.c ├── Drivers/ │ ├── CMSIS/ │ └── STM32F4xx_HAL_Driver/ ├── Docs/

│ ├── Design Document.md │ ├── User Manual.md │ └── Debug Log.md ├── MDK-ARM/ └── README.md The principle of module division is high cohesion and low coupling. adc.c is only responsible for ADC initialization, DMA configuration, and buffer read/write management; trigger.c only handles trigger detection; ui.c only handles screen drawing and menu interaction; and main.c only does initialization calls and main-loop scheduling. The benefit of splitting it this way is that if you don't want to use my UI, you can simply replace ui.c; if you want to expand to dual channels, you only need to change adc.c and trigger.c, and the other modules don't need to be touched. 3.2 ADC/DMA Sampling Core Configuration, Explained Line by Line The key to ADC configuration lies in the sampling period and the DMA mode. The following is the core snippet of the initialization code in adc.c: void MX_ADC1_Init(void) { ADC_ChannelConfTypeDef sConfig {0}; hadc1.Instance ADC1; hadc1.Init.ClockPrescaler

ADC_CLOCK_SYNC_PCLK_DIV4; // ADCCLK 84MHz/4 21MHz hadc1.Init.Resolution ADC_RESOLUTION_12B; // 12-bit resolution hadc1.Init.ScanConvMode DISABLE; // single-channel scan mode disabled hadc1.Init.ContinuousConvMode ENABLE; // continuous conversion mode hadc1.Init.DiscontinuousConvMode DISABLE; hadc1.Init.ExternalTrigConvEdge ADC_EXTERNALTRIGCONVEDGE_NONE; // software trigger hadc1.Init.DataAlign ADC_DATAALIGN_RIGHT; hadc1.Init.NbrOfConversion 1; HAL_ADC_In

it(hadc1); sConfig.Channel ADC_CHANNEL_0; // PA0 sConfig.Rank 1; sConfig.SamplingTime ADC_SAMPLETIME_1CYCLE_5; // 1.5-cycle sampling HAL_ADC_ConfigChannel(hadc1, sConfig); } ClockPrescaler PCLK_DIV4 corresponds to ADCCLK 21MHz. The F407's ADC allows a maximum of 36MHz, so 21MHz leaves a margin to ensure conversion accuracy. The 1.5-cycle SamplingTime is the key to the highest sampling rate: the 12-bit conversion itself needs 12 cycles, so the total sampling period is 1.5+12 = 13.5 cycles, giving a sampling rate of 21MHz/13.5 ≈ 1.56Msps. DMA configuration is another key point. I used circular mode plus double buffering; the code in main.c is: static uint16_t adc_buf[2][ADC_BUF_SIZE]; //

double buffering, 12800 points per block // start the ADC's DMA transfer HAL_ADC_Start_DMA(hadc1, (uint32_t *)adc_buf, ADC_BUF_SIZE * 2); Once the DMA is configured in circular mode, a HalfTransfer interrupt fires when the first half of the buffer is filled, and a TransferComplete interrupt fires when the second half is filled; flags are set in the two interrupt callbacks respectively, and the main loop reads the flags and processes the corresponding buffer data. This implements a pipeline operation of "the DMA keeps sampling while the CPU processes the previous block," so no sample points are lost and the UI doesn't stutter. 3.3 Trigger Detection Logic: Making the Waveform Stop Steadily Trigger detection is written in trigger.c. The core idea is to first find in the buffer the position satisfying "the previous point was below the threshold and the current point is above it," then use this point as a reference to extract a complete screen of data. The code: uint16_t FindTriggerEdge(uint16_t *buf, uint16_t len, uint16_t threshol

d) { for (uint16_t i 1; i len; i) { if (buf[i - 1] threshold buf[i] threshold) { return i; // return the buffer index of the rising-edge trigger point } } return 0xFFFF; // return an invalid value if no edge is found } The trigger modes are implemented in trigger.c as well, with three modes: rising-edge trigger, falling-edge trigger, and auto trigger. Auto trigger means that if no edge is found within the set time, the current buffer data is displayed directly without extraction or alignment. This way, even if the signal frequency is too low and there are too few edges, the screen won't go blank. In actual debugging I found that simple edge detection isn't enough—it's prone to false triggers at noise. I added a "debounce" logic in the code: after a trigger point is detected, the following N sample points must all remain above the trigger level before it's confirmed as a valid trigger. The value of N depends on the sampling rate; the default is 16, and in high-noise environments you can raise it to 64, at the cost of a slightly larger trigger delay. 3.4 LCD Waveform Drawing: From Bare Pixel Plotting to Framebuffer Refresh I used a 2.8-inch

本文来源:http://www.lpqz.cn/news/52666
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

暂无评论,快来发表第一条评论吧!No comments yet. Be the first!

📮 需求咨询📮 Inquiry