
本文来源:https://post.smzdm.com/p/ad7zoq6d
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
一块华为 nova 14 Pro 的彩显手机壳,二手不到 20 元还包邮,背面是一整块 3.98 英寸四色墨水屏。DIY 圈盯上的是这块拆机屏本身:型号 JD79665AA,768×552,黑白黄红四色,2bpp。 哔哩哔哩 GitHub
同类墨水屏手机壳,别家原价三四百。华为这块便宜,是因为它本来就只是配件,官方标注 nova 14 Ultra 和 nova 14 Pro 可用,换个机型根本刷不了图。转折在 10 月 16 日:B 站 up 主氧化钙硼把这套原厂通信协议逆向了出来,软件和源码直接开源到 Gitee。那条视频如今已有 15 万播放、3800 多收藏,往后一个月,方案接连落地。 知乎 小红书 哔哩哔哩
这块屏本来就是无源的,原厂靠无线充电线圈加 NFC 供电传数据。所以最省事的玩法不是拆它,是照着原样喂它。氧化钙硼用的是 PN532 读卡器 ,11 月 9 日 PN5180 方案也被跑通并开源,省掉了额外电容,壳买回来拆了包装就能用。ESP32-C3 通过硬件 SPI 驱动 PN5180,靠 13.56MHz 正弦波载波给屏做能量收集与升压,整条链路不需要 电池 ;刷完射频断电,画面靠微胶囊的双稳态特性永久留着。设备自己开个叫 EPD-3.98-NFC 的热点,手机连上就弹出网页工作台。 哔哩哔哩 GitHub
裁图、旋转、色调映射、抖动、LZO1X 压缩全丢给手机或电脑的浏览器执行,单片机只管收帧刷屏。走得更远的是安卓阅读器"墨读 InkReader":整页原始数据约 106KB,老办法要拆成 476 个小包,每翻一页都重传整张图。它换成 LZO1X 压缩加后台预传下一页,实际只要 55 包,同页负载从 106620 字节降到 7795 字节。 GitHub GitHub
拆屏直驱:10 块钱的 ESP32-C3 焊上去
想要电池、按键、让它自己连 WiFi,就得拆屏直驱。主控普遍用 ESP32-C3 SuperMini,不到 10 块钱。这条路上最完整的是墨印 MoInk:外壳在 MakerWorld,固件在 GitHub,配一键刷机包。不装 App、不用 服务器 ,设备自带热点与门户引导页,手机连上自动弹出创作页,选图、裁剪、风格化、加字,一键推屏。图库最多存 8 张离线轮播,双击按键换图,GPIO2 做供电自锁,插 USB 时不往电池倒灌。 知乎 GitHub
11 月 13 日,作者"一般社畜小兽人"补上了最难的一环:免飞线 FPC 板。以前社区方案是拿 ESP32-C3 SuperMini 往 24pin 排线上飞线,接线繁琐、良率靠手感;现在一块软板直接叠加、对位焊接在原屏驱动板上,他自己的说法是草履虫也不会焊错。板上带无线充、Type-C、锂电池三电源切换和 TP4057 充电管理,一键开机自锁、能软关机——不然开发板那颗 LED 长亮,续航急剧降低。对焊接没信心的,把软板电源部分剪掉、短接按键焊盘就行,剩下和普通飞线一样。 哔哩哔哩
拆屏先拆掉一块玻璃。 背板是玻璃,胶必须加热透。评论区最常见的结局:吹风机吹热风刮四周,玻璃碎一半;或者压根没加热就硬撬,壳和屏一起废。加热过头更狠,有人在评论区一口气认了三块屏:第一块掀玻璃盖板崩碎背面,第二块切小板滑过头,第三块直接加热过头,热固粒子驱动不显示了。稳一点是用电热膜,或者吹风机控在 110℃ 左右吹两分钟;也有人说酒精浸润几分钟就能无损拿下。 哔哩哔哩 哔哩哔哩 哔哩哔哩
FPC 打样不便宜。 有人兴冲冲去嘉立创复刻那块免飞线软板,报价 170 元。想省钱得蹲打样券。 哔哩哔哩
别拿它当副屏。 这是最容易翻车的心态。彩色灰阶加高刷是 11 月 6 日才刚被跑通的,作者自己在简介里写的原话是"4fps 似乎真的能用"。抖动算法到现在都没开源,社区实测的结论也很直白:色阶要几十秒,快刷只能黑白而且残影很重。这离"能当副屏"还差得远。 哔哩哔哩 哔哩哔哩
往底层看限制更硬:SPI 速率卡住了纯显存写入带宽,上限约 2.13MB/s,全屏写一次就要 56ms,靠反复触发 RST 复位能提速,但复位多了屏会"烧屏"。何况墨水屏刷新本来就分全刷、快刷、局刷:全刷要走完擦除、激活、显示三个阶段,屏幕还得黑白交替闪好几次。局刷最快,代价是边缘残影;四色屏多一层黄色粒子,只会更慢。 哔哩哔哩 知乎
静态、低频、要好看。照片墙、冰箱贴、NFC 工牌、桌面电子 拍立得 、门口信息牌——刷一次挂一个月,几乎零功耗,整套 25 元内就能搞定。已经有人做好一个又买了三个,凑成四面相框墙。 哔哩哔哩 哔哩哔哩
不适合:看漫画、当电脑副屏、任何需要每秒刷新的东西。
20 多元买一块 768×552 的四色墨水屏,这价格在 DIY 圈没有对手。但先想清楚你要的是"一张会自己换的画",还是"一块能动的屏"——前者现在就能做,后者还得等社区把波形啃完。

本文来源:https://post.smzdm.com/p/ad7zoq6d
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
A colour-display phone case for the Huawei nova 14 Pro sells second-hand for under 20 yuan including postage, and its back is a complete 3.98-inch four-colour e-paper panel. What caught the DIY community's attention was the panel itself: a JD79665AA, 768x552, black-white-yellow-red at 2 bpp. Comparable e-ink phone cases from other brands cost three or four hundred yuan at list price. Huawei's is cheap because it is only an accessory, officially supported on the nova 14 Ultra and nova 14 Pro, and on any other handset it cannot even refresh an image.
The turning point came on October 16, when Bilibili creator 氧化钙硼 reverse-engineered the original communication protocol and open-sourced the software and source code on Gitee. The panel is passive: the original design powers it and transfers data through a wireless charging coil plus NFC. So the easiest route is not to tear it apart but to feed it the way Huawei did — the creator used a PN532 reader, and on November 9 a PN5180-based solution was also proven and open-sourced, eliminating extra capacitors so the case works straight out of the box. An ESP32-C3 drives the PN5180 over hardware SPI.
Because the panel is dumb, all the heavy work is pushed to a browser on a phone or PC: cropping, rotation, colour mapping, dithering and LZO1X compression. The microcontroller only receives frames and refreshes the screen. The Android reader InkReader took this further — a full page of raw data is about 106 KB, which the old approach split into 476 small packets and retransmitted entirely on every page turn; with LZO1X compression and background prefetching of the next page it needs only 55 packets, and page turns become noticeably faster.
The other path is to remove the panel and drive it directly, which is necessary if you want a battery, buttons and Wi-Fi. Builders generally use an ESP32-C3 SuperMini costing under 10 yuan. The most complete project is MoInk: the shell is on MakerWorld, the firmware and a one-click flashing package on GitHub. It needs no app and no server — the device creates its own hotspot and a captive portal, so a phone connects and is guided through setup — making the 20-yuan case a surprisingly capable standalone e-reader.