
Seeed 推出的 XIAO STM32C5 售价 9.9 美元,在一块 21×17.8 毫米的机器人开发板上集成了 144 MHz 的 Cortex-M33 内核、两路 CAN FD 控制器以及一颗可自加热的六轴 IMU。
这是 XIAO 家族首款基于意法半导体(STMicroelectronics)MCU 的开发板,规格明显面向机器人与工业创客:双路 CAN FD 加上一颗能自我保温的运动传感器。
核心配置:STM32C5A3CG,144 MHz Arm Cortex-M33(带 FPU 与 DSP 指令),256KB SRAM、1MB 片内 Flash,外挂 16MB Flash;板载 TI TCAN3403-Q1 收发器提供一路 CAN FD,并保留 USB-C;传感器为 LSM6DS3TR-C 六轴 IMU,四周环绕 PWM 可控加热电阻以抑制温漂。售价 9.9 美元(预焊版 10.9 美元)。
多数拇指大小的开发板都在卷无线功能,这块板子却押注有线可靠性。CAN FD 是汽车、机器人与工厂设备中 CAN 总线的更高带宽继任者,在如此小的板子上放两路控制器颇为少见。
惯性传感器会随温度变化产生漂移——这对平衡机器人、无人机与运动追踪很关键。据 CNX Software,Seeed 在 IMU 周围布置了十颗加热电阻,最高产生 0.58W 热量,固件可预热传感器并利用其内部温度读数保持稳定,这一手法通常只在更昂贵的导航硬件上出现。
软件方面,Seeed Wiki 提供 STM32CubeIDE、PlatformIO(Zephyr RTOS)与 MicroPython 的支持,含 CAN FD 与 IMU 示例、引脚映射、原理图及 KiCad/Eagle 设计文件;供电为 USB-C 5V 或 3.7V 锂电池并带充放电管理,调试走 SWD,扩展为两排 7-pin 排针与半孔焊盘,提供 GPIO、ADC、I2C、SPI、UART。
本文来源:https://thequantumdispatch.com/articles/seeed-xiao-stm32c5-can-fd-imu-board
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
Seeed's $9.90 XIAO STM32C5 packs a 144 MHz Cortex-M33, two CAN FD controllers and a self-heating 6-axis IMU into a 21 x 17.8 mm robotics board.
Seeed Studio's XIAO family keeps growing, and its newest member is a first: the XIAO STM32C5 is the company's first XIAO development board built around an STMicroelectronics microcontroller, with dual CAN FD and a motion sensor that can keep itself warm.
MCU: STM32C5A3CG, a 144 MHz Arm Cortex-M33 with FPU and DSP instructions, 256KB SRAM and 1MB internal flash, plus 16MB external flash. Connectivity: two CAN FD controllers, one wired to an onboard TI TCAN3403-Q1 transceiver, and a USB-C port. Sensor: an LSM6DS3TR-C 6-axis IMU surrounded by PWM-controlled heating resistors to reduce temperature drift. Price: $9.90 on the Seeed Studio store, or $10.90 pre-soldered, in the standard 21 x 17.8 mm XIAO footprint.
Most thumb-sized development boards chase wireless features. This one leans into wired reliability. CAN FD is the higher-bandwidth successor to the CAN bus used in cars, robots and factory equipment, and having two controllers on a board this small is unusual.
Inertial sensors drift as their temperature changes, which matters for balancing robots, drones and motion tracking. According to CNX Software, Seeed surrounded the IMU with an array of ten heating resistors generating up to 0.58W. Firmware can preheat the sensor and use its internal temperature reading to hold it steady, a technique usually seen in pricier navigation hardware.
Software Support and Specs at a Glance: Seeed's wiki documents development with STM32CubeIDE, PlatformIO with Zephyr RTOS and MicroPython, and includes CAN FD and IMU examples, pin mapping, schematics and KiCad and Eagle design files. Power: 5V over USB-C or a 3.7V Li-ion/LiPo battery, with onboard charging and battery voltage monitoring. Debugging: SWD through solder pads. Expansion: two 7-pin headers and castellated holes with GPIO, ADC, I2C, SPI and UART.