本文来源:https://mp.weixin.qq.com/s/gZxtIT8XN9fR5v9rY77GiQ
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。Seeed Studio(矽递科技)近期与开源项目 OpenDisplay 达成合作,上线两款面向智能家居场景的电子纸仪表盘开发套件,依托低功耗蓝牙 BLE 与 OpenDisplay 开源固件方案,主打超长续航,为 DIY 玩家与智能家居开发者带来轻量化的信息面板方案。

OpenDisplay 源自 OpenEPaperLink 项目,也是 Open Home Foundation 开放智能家居生态的合作项目。这套方案采用独特的发送端 + 接收端分离架构:图像渲染、色彩转换、图像抖动等算力消耗较大的任务,统一交由发送设备完成,处理完成后的图像数据再通过 BLE 下发给电子纸终端。电子纸接收端仅负责刷新画面,无需承担复杂运算,最大限度压低终端功耗,充分释放电子墨水屏只在刷新耗电的特性优势。

本次矽递推出的两款硬件,正是这套架构中的接收终端,搭载 Nordic nRF52840 主控,片上集成 1MB Flash、256KB SRAM,额外搭载 2MB 外置闪存,出厂预刷 OpenDisplay 开源固件,开箱即可接入生态。
4.26 英寸灰度款:分辨率 800×480,支持 4 级灰度;内置 2000mAh 电池,每 15 分钟刷新一次画面的条件下,续航最长可达 2 年;售价 39.90 美元。
7.3 英寸彩色款:采用 E Ink Spectra 6 六色电子纸,同样为 800×480 分辨率,可呈现黑、白、红、黄、绿、蓝六色,依靠抖动算法实现丰富视觉效果;同样搭载 2000mAh 电池,每 2 小时刷新一次,续航约 1 年;售价 75.90 美元。
两款套件标配 3D 打印支架,支持横屏、竖屏摆放,适合放置在桌面,用来展示家庭温湿度、传感器数据、日程日历、家居设备状态等静态信息。值得注意的是,终端本身没有 Wi-Fi 模块,无法独立联网,必须搭配一台 BLE 发送设备生成画面、推送数据。同时电子纸原生不配备背光,刷新速度偏慢,更适合静态信息展示,并不适合播放动态画面。
这套产品面向开源爱好者、智能家居改造玩家,依托开放固件,支持自主二次开发,批量采购还可享受优惠,目前已经在 Seeed 官方商店正式发售。
Source: https://mp.weixin.qq.com/s/gZxtIT8XN9fR5v9rY77GiQ
For copyright matters, please contact 13951431913#139.com or leave a comment on the right.
Seeed Studio has partnered with the open-source project OpenDisplay to launch two e-paper dashboard development kits for smart home scenarios. Built on low-power Bluetooth LE and OpenDisplay's open-source firmware, they emphasize ultra-long battery life, offering DIY enthusiasts and smart home developers a lightweight information-panel solution.

OpenDisplay originated from the OpenEPaperLink project and is also a partner project of the Open Home Foundation's open smart home ecosystem. The design uses a distinctive separate transmitter and receiver architecture: compute-intensive tasks such as image rendering, color conversion and dithering are all handled by the transmitting device, and the resulting image data is then sent over BLE to the e-paper terminal. The receiver only refreshes the screen and performs no complex computation, minimizing terminal power draw and making full use of the fact that e-ink consumes power only when refreshing.

The two hardware kits from Seeed Studio are precisely the receiving terminals in this architecture. They use a Nordic nRF52840 MCU with 1 MB on-chip Flash and 256 KB SRAM, plus 2 MB of external flash, and ship pre-flashed with OpenDisplay open-source firmware for out-of-the-box connectivity to the ecosystem.
.26-inch grayscale model: 800×480 resolution with 4-level grayscale; a built-in 2000 mAh battery delivers up to two years of life when refreshing every 15 minutes; priced at US$39.90.
7.3-inch color model: built on E Ink Spectra 6 six-color e-paper, also at 800×480, capable of black, white, red, yellow, green and blue, with dithering algorithms producing rich visuals; also with a 2000 mAh battery, about one year of life when refreshing every two hours; priced at US$75.90.
Both kits include a 3D-printed stand and support landscape or portrait placement, making them suitable for a desk to show static information such as indoor temperature and humidity, sensor data, calendars and schedules, and device status. Notably, the terminals have no Wi-Fi module and cannot connect to the internet on their own — a BLE transmitter is required to generate images and push data. E-paper also has no backlight and refreshes relatively slowly, so it is better suited to static information than to moving images.
Aimed at open-source enthusiasts and smart home tinkerers, the products support independent secondary development through open firmware, with discounts available for bulk orders. They are now on sale in Seeed's official store.