
[Dave Farquhar] 带我们怀旧地回顾了 Commodore 1600 VICModem,它或许是第一款售价低于 $100 的电话调制解调器。众所周知,Commodore 以制造更便宜的计算机(如 VIC20、Commodore 64)以及低成本外设(如磁盘驱动器)而闻名。但在当时,竞争对手的 300 baud 调制解调器售价至少是它的两倍,而一台 1200 baud 的设备至少要 $600,Commodore 是怎么把这款调制解调器做到 $100 价位的呢?
首先,Commodore 并没有自己做设计。相反,他们把设计外包给了知名调制解调器制造商 Anchor Automation。该设计使用 Motorola MC14412 这款片上调制解调器芯片,并搭配另外六枚芯片。理论上这颗芯片可以做到 600 baud,但该调制解调器的标称速率为 300 baud。不过它确实在设计上做了一些有趣的取舍。
老式调制解调器不允许直接接入电话线路,所以你要先拨电话号码,然后把听筒塞进一种带软垫托槽、称为“声耦合器”(acoustic coupler)的装置里——它把麦克风放在电话听筒旁,把扬声器放在电话麦克风旁。现代调制解调器没有这个问题(部分要归功于 Tom Carter),VICModem 也可以直接连接。但为了省钱,它无法替你拨号。其思路是:你要像使用老式声学调制解调器那样先拨电话,然后再把听筒线拔下、自己插到调制解调器上。
但这里有个问题。那个年代的旧电话并不总是在听筒上带插头。讽刺的是,据 [Dave] 说,这家公司在加拿大买了一些电话想与调制解调器捆绑销售,结果发现这些电话的听筒是硬接线的,根本无法使用。不仅如此,就算这些电话型号合适,当时在加拿大也可能会违法,因为电话管理规定不允许听筒使用模块化插孔。
为了解决这个问题,他们还推出了 VIC-1605 作为配套组件——本质上就是一根用于电话的 Y 型线缆。你把它插到墙上,然后把电话接到 RJ-11 口,把调制解调器接到 RJ-9 口。
此外还有其他节省成本的做法。例如,设备上有一个开关,用来判断你是在发起呼叫还是在接听来电。除了电话接口上的那个失策之外,这也算是一个“如何把东西设计得尽可能便宜”的典型例子。
如今已经很难找到调制解调器了,但即便你仍对它们怀有怀念,也会惊讶于它们其实有多么古老,以及要做一台低速声学调制解调器所需要的东西其实少得惊人。
本文来源:https://hackaday.com/2026/10/30/a-1982-modem-for-100/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
[Dave Farquhar] takes a walk down memory lane about the Commodore 1600 VICModem , perhaps the first phone modem to sell for less than $100. Commodore, of course, was famous for making cheaper computers like the VIC20, the Commodore 64, and lower-cost peripherals like disk drives. But how did they hit the $100 price point with the modem when competing 300 baud modems sold for at least twice that, and a 1200 baud unit would set you back at least $600?
First, Commodore didn’t handle the design themselves. Instead, they outsourced to Anchor Automation, a well-known modem manufacturer. It used a Motorola MC14412 modem on a chip, along with six other chips. The chip could, in theory, do 600 baud, but the modem was rated for 300. But it did make some interesting design choices.
Old-school modems were not allowed to connect to the phone lines directly, so you dialed the phone number and then shoved the handset into some padded cups known as an acoustic coupler that placed a microphone next to the phone speaker and a speaker next to the phone microphone. Modern modems didn’t have this problem (thanks, in part, to Tom Carter ), and the VICModem also connected directly. But to save money, it couldn’t dial the phone for you. The idea was you’d dial the phone like you would with an old acoustic modem and then pull the handset cord and plug it into the modem yourself.
There was a problem. In those days, old phones didn’t always have a plug on the handset. Ironically, according to [Dave], the company bought phones to bundle with the modem in Canada only to find out the phones they bought had hard-wired handsets and were not usable. Not only that, if the phones had been the right kind, they would have been illegal in Canada at that time since the phone rules prohibited modular jacks for the handset.

To fix the problem, they also bundled the VIC-1605, which was essentially a Y cable for the phone. You plugged it into the wall, and then plugged the phone into an RJ-11 and the modem into an RJ-9.
There were other cost savings, too. There was a switch that determined if you were originating a call or receiving one, for example. A great example of how to design something as cheaply as possible, other than the faux pas with the phone connectors.
These days, it is hard to find a modem, but even if you do remember them fondly, it is surprising how old they really are and how little you needed to make a low-rate acoustic modem.