BeagleConnect QuadESC 四通道无刷电机控制器:基于 TI AM13E23019 扭矩模块BeagleConnect QuadESC 4-channel BLDC motor controller uses TI's AM13E23019-based Torque module


AI free token/AI免费积分
BeagleConnect QuadESC 四通道无刷电机控制器:基于 TI AM13E23019 扭矩模块

BeagleBoard.org 推出了 BeagleConnect QuadESC——一款基于 BeagleConnect Torque SoM 构建的开源四通道 BLDC 电机控制器/载板。该 SoM 搭载 TI 的 200 MHz AM13E23019 Arm Cortex-M33 微控制器,并配备三角函数运算单元 (TMU) 以及用于边缘 AI 应用的 TinyEngine 神经网络加速器。

QuadESC 载板支持四路三相 BLDC 电机输出、十二路电流检测与十二路电压检测通道、四个温度传感器以及电池电压监测。它还包含一个带有 DShot、遥测和电流上报信号的八针飞控连接器,以及 SWD 调试、蜂鸣器连接器和板载电源稳压。

Torque SoM 也可集成到定制载板中,用于机器人、电机控制以及 CAN 连接应用。它提供处理、传感和通信接口,而电机电源由外部硬件提供。

主 MCU – Texas Instruments AM13E23019

CPU 核心 – Arm Cortex-M33 MCU @ 200 MHz with FPU

存储 – 128KB SRAM

闪存 – 512KB flash

其他特性 – TMU、TinyEngine AI accelerator、3x 12-bit ADCs 以及电机控制 PWM

CPU 核心 – Arm Cortex-M33 MCU @ 200 MHz with FPU

其他特性 – TMU、TinyEngine AI accelerator、3x 12-bit ADCs 以及电机控制 PWM

CAN FD,板载 TI TCAN844 收发器

4 针 JST-GH CAN/电源连接器,支持软件选择 120Ω 终端

UART、SPI 和 I²C 接口

CAN FD,板载 TI TCAN844 收发器

4 针 JST-GH CAN/电源连接器,支持软件选择 120Ω 终端

UART、SPI 和 I²C 接口

100 焊盘底部 LGA 接口,1.27 mm 间距(位于背面)

2x 12 针扩展排针,引出 UART、SPI、模拟、PWM 和控制信号

通过载板接口提供 30 条指定的模拟输入通道

Qwiic 连接器,用于 3.3V I²C 传感器和配件

100 焊盘底部 LGA 接口,1.27 mm 间距(位于背面)

2x 12 针扩展排针,引出 UART、SPI、模拟、PWM 和控制信号

通过载板接口提供 30 条指定的模拟输入通道

Qwiic 连接器,用于 3.3V I²C 传感器和配件

调试 – 8 针连接器,用于 SWD、UART、复位、启动选择、接地和调试电源

安全 – 硬件支持安全启动、安全调试、安全固件更新以及加密加速

电源 – 稳压 5V 载板输入、板载 3.3V 稳压,以及独立的 3.3V 调试电源支持

尺寸 – 25.4 x 38.1 mm(四层,1.6 mm PCB)

该模块需要独立的模拟基准 (VAA) 用于 ADC 测量,以及 5V 电源用于 CAN 通信。它还必须接收经过稳压的载板电源,而不是原始电池电压。

BeagleConnect Torque 顶视图

BeagleConnect Torque 底视图

BeagleConnect QuadESC 载板

QuadESC 面向机器人、无人机以及其他多电机应用,尺寸为 60 x 48 mm,并支持 3S 至 6S 电池。它对每台电机使用独立的 PWM 控制,并采用同步电流测量以实现磁场定向控制 (FOC)。

控制器 – 如上所述的 BeagleConnect Torque SoM

4x Texas Instruments DRV8323SRTAR 三相栅极驱动器,支持 SPI 配置、电流检测放大器和故障上报

12x TI CSD88599Q5DC 半桥器件(每台电机三个)

4x 独立三相 BLDC 电机通道

每个通道配备专用电机控制 PWM 模块

当前设计目标 – 每台电机 40A 连续、70A 峰值(取决于热验证)

4x Texas Instruments DRV8323SRTAR 三相栅极驱动器,支持 SPI 配置、电流检测放大器和故障上报

12x TI CSD88599Q5DC 半桥器件(每台电机三个)

4x 独立三相 BLDC 电机通道

每个通道配备专用电机控制 PWM 模块

当前设计目标 – 每台电机 40A 连续、70A 峰值(取决于热验证)

12x 低侧相电流测量(每台电机三路)

4x NTC 温度传感器,靠近功率级

通过 Torque 模块的三个 12-bit ADC,用于同步相电流测量

12x 低侧相电流测量(每台电机三路)

4x NTC 温度传感器,靠近功率级

通过 Torque 模块的三个 12-bit ADC,用于同步相电流测量

通过 BeagleConnect Torque 模块的 CAN-FD

8 针飞控接口,包含四条 DShot 信号线路、遥测、电流上报、电池电压和接地

4x 三相电机连接 (J2–J5) 以及专用电池焊接端子 (J1)

通过 BeagleConnect Torque 模块的 CAN-FD

8 针飞控接口,包含四条 DShot 信号线路、遥测、电流上报、电池电压和接地

4x 三相电机连接 (J2–J5) 以及专用电池焊接端子 (J1)

调试 – 10 针 ARM/JTAG 调试排针,支持 SWD 访问

本文来源:https://www.cnx-software.com/2026/10/29/beagleconnect-quadesc-4-channel-bldc-motor-controller-ti-am13e23019-based-torque-module/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

BeagleBoard.org has introduced the BeagleConnect QuadESC, an open-source 4-channel BLDC motor controller/carrier board built around the BeagleConnect Torque SoM. The SoM features TI’s 200 MHz AM13E23019 Arm Cortex-M33 microcontroller with a trigonometric math unit (TMU) and a TinyEngine neural-network accelerator for edge AI applications.

The QuadESC carrier board supports four three-phase BLDC motor outputs, twelve current and twelve voltage sensing channels, four temperature sensors, and battery voltage monitoring. It also includes an eight-pin flight controller connector with DShot, telemetry, and current reporting signals, along with SWD debugging, a buzzer connector, and onboard power regulation.

The Torque SoM can also be integrated with custom carrier boards for robotics, motor control, and CAN-connected applications. It provides the processing, sensing, and communication interfaces, while external hardware supplies the motor power.

Main MCU– Texas Instruments AM13E23019 CPU core – Arm Cortex-M33 MCU @ 200 MHz with FPU Memory – 128KB SRAM Storage – 512KB flash Other features – TMU, TinyEngine AI accelerator , 3x 12-bit ADCs, and motor-control PWM.

CPU core – Arm Cortex-M33 MCU @ 200 MHz with FPU

Other features – TMU, TinyEngine AI accelerator , 3x 12-bit ADCs, and motor-control PWM.

Connectivity CAN FD with onboard TI TCAN844 transceiver 4-pin JST-GH CAN/power connector with software-selectable 120Ω termination UART, SPI, and I²C interfaces

CAN FD with onboard TI TCAN844 transceiver

4-pin JST-GH CAN/power connector with software-selectable 120Ω termination

Expansion 100-pad underside LGA interface with 1.27 mm pitch (on the back side) 2x 12-pin expansion rows exposing UART, SPI, analog, PWM, and control signals 30 assigned analog-input routes through the carrier interface Qwiic connector for 3.3V I²C sensors and accessories

100-pad underside LGA interface with 1.27 mm pitch (on the back side)

2x 12-pin expansion rows exposing UART, SPI, analog, PWM, and control signals

30 assigned analog-input routes through the carrier interface

Qwiic connector for 3.3V I²C sensors and accessories

Debugging – 8-pin connector for SWD, UART, reset, boot selection, ground, and debug power

Security – Hardware support for secure boot, secure debug, secure firmware updates, and cryptographic acceleration

Power – Regulated 5V carrier input, onboard 3.3V regulation, and separate 3.3V debug-power support

Dimensions – 25.4 x 38.1 mm (four-layer, 1.6 mm PCB)

The module requires a separate analog reference (VAA) for ADC measurements and a 5V supply for CAN communication. It must also receive regulated carrier power, not raw battery voltage.

BeagleConnect QuadESC 4-channel BLDC motor controller uses TI's AM13E23019-based Torque module

BeagleConnect Torque Top View BeagleConnect Torque Bottom View

Designed for robotics, drones, and other multi-motor applications, the QuadESC measures 60 x 48 mm and supports 3S to 6S batteries. It uses separate PWM control for each motor and synchronized current measurements for field-oriented control (FOC).

Controller – BeagleConnect Torque SoM as mentioned above

Motor control 4x Texas Instruments DRV8323SRTAR three-phase gate drivers with SPI configuration, current-sense amplifiers, and fault reporting 12x TI CSD88599Q5DC half-bridge devices (three per motor) 4x independent three-phase BLDC motor channels Dedicated motor-control PWM module for each channel Current design targets – 40A continuous and 70A burst per motor (subject to thermal validation)

4x Texas Instruments DRV8323SRTAR three-phase gate drivers with SPI configuration, current-sense amplifiers, and fault reporting

12x TI CSD88599Q5DC half-bridge devices (three per motor)

4x independent three-phase BLDC motor channels

Dedicated motor-control PWM module for each channel

Current design targets – 40A continuous and 70A burst per motor (subject to thermal validation)

Sensing 12x low-side phase-current measurements (three per motor) 12x phase-voltage measurements 4x NTC temperature sensors near the power stages Three 12-bit ADCs through the Torque module for synchronized phase-current measurements

12x low-side phase-current measurements (three per motor)

4x NTC temperature sensors near the power stages

Three 12-bit ADCs through the Torque module for synchronized phase-current measurements

Connectivity CAN-FD through the BeagleConnect Torque module 8-pin flight-controller interface with four DShot signal routes, telemetry, current reporting, battery voltage, and ground 4x three-phase motor connections (J2–J5) and dedicated battery solder terminals (J1)

CAN-FD through the BeagleConnect Torque module

8-pin flight-controller interface with four DShot signal routes, telemetry, current reporting, battery voltage, and ground

4x three-phase motor connections (J2–J5) and dedicated battery solder terminals (J1)

Debug – 10-pin ARM/JTAG debug header with SWD access

暂无评论,快来发表第一条评论吧!No comments yet. Be the first!

📮 需求咨询📮 Inquiry