把旧手机主板改造成 RC 飞机遥控器Turning An Old Phone's Motherboard Into An RC Plane Controller


AI free token/AI免费积分
把旧手机主板改造成 RC 飞机遥控器

将智能手机进行升级再造非常有意义,尤其是因为其中有许多组件在作为手机的吸引力消退之后很久仍然有用。以 Mountain DS Lab 为例,他们选择用一部 8 年前的 Xiaomi Mi 8 手机,借助该手机的 LTE 蜂窝网络连接,为一架遥控飞机添加远距离 FPV 视频链路与遥控功能。

这部智能手机是二手购得,价格为 23 美元,他们将原厂 Xiaomi ROM 刷成了 LineageOS,从而在上面获得更轻量且更新的 Android 系统。从视频中可以清楚看出,这部手机已经有些磨损:玻璃后盖开裂,显示屏上还出现了几条难看的条纹。幸运的是,他们只需要这块主板本身。

这里有个需要注意的问题:该操作系统在启动时会检测显示屏,如果未检测到就会超时,可能会完全中断启动过程。解决办法是在设备树(device tree)中禁用显示屏,这需要按照视频中的说明修改 boot.img 文件。随后,他们打印了一个主板的定制支架,以便将其安装在目标飞机内部。

为了与航电系统通信,他们制作了一块带有 CH340 IC 的 USB 转 UART 适配器 PCB。然后将其连接起来进行首次测试,并将扩展的前置摄像头用作自定义 Android 应用的 FPV 摄像头。通过远程 LTE 链路使用控制器与飞控协同工作正常,因此接下来他们将飞机组装起来进行初步测试。

从这一阶段开始,剩余工作主要是常规的遥控飞机组装与测试,只不过把通常基于射频的控制与 FPV 链路替换成了 LTE 链路。遗憾的是,在创作者居住地附近不允许放飞无人机,因此在其首飞之前只进行了一些滑行测试;首飞将在当地的一条简易跑道进行,并将出现在后续视频中。

当然,这种遥控方式并非首次出现,持续的俄乌战争就是基于 LTE 遥控无人机的典型例子。尽管我们并不提倡用升级改造的智能手机去摧毁一个国家三分之一的战略轰炸机队,但归根结底这属于同一项技术,而且也是制造一架 RC 无人机的好办法,使其续航距离能够超越 2.4 GHz 链路所能勉强达到的几公里范围。只是要做好心理准备:LTE 链路会增加几毫秒的延迟。

本文来源:https://hackaday.com/2026/10/28/turning-an-old-phones-motherboard-into-an-rc-plane-controller/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

Upcycling smartphones makes a lot of sense, especially since they contain so many components that remain useful long after their desirability as a smartphone has faded. In the case of [Mountain DS Lab], they opted to use an 8-year old Xiaomi Mi 8 phone to add long-range FPV video link and remote control functionality to an RC plane, using the phone’s LTE cellular connectivity.

The smartphone was bought used for $23, with the default Xiaomi ROM overwritten by LineageOS to get a more lightweight and up to date Android installation on it. From the video it’s clear that this phone has seen better days, with the glass back cracked and a few ugly lines running across the display. Fortunately all that is needed is the motherboard itself.

One gotcha here is that the OS checks for the display on boot and will time-out if it’s not present, potentially halting the process entirely. The workaround requires disabling the display in the device tree, which is done by modifying the boot.img file as explained in the video. Next a custom bracket for the motherboard was printed so that it could be fitted inside the target airplane.

To communicate with the avionics, a USB-to-UART adapter PCB was created with a CH340 IC on it. This was then connected together for an initial test, with the extended front camera being used as the FPV camera for the custom Android application. Using the controller via the remote LTE link worked with the flight controller, so next the airplane was assembled for initial testing.

Turning An Old Phone's Motherboard Into An RC Plane Controller

From this point it’s all pretty standard RC airplane assembly and testing, just with the typical RF-based control and FPV link replaced with the LTE link. Unfortunately flying drones isn’t permitted in the immediate area where the creator lives, so only some taxiing was tried prior to its maiden flight at a local airstrip that will be featured in an upcoming video.

Naturally, this isn’t the first time that someone has tried this type of remote control, with the ongoing Russo-Ukraine war being a prime example of LTE-based remote control of drones. Although we do not advocate wiping out a third of a nation’s strategic bomber fleet with upcycled smartphones, ultimately this is the same technology and a good way to create an RC drone that can last more than the few kilometers eked out from a 2.4 GHz link or so. Just be prepared for the LTE link to add a few milliseconds of latency.

暂无评论,快来发表第一条评论吧!No comments yet. Be the first!

📮 需求咨询📮 Inquiry