
飞利浦 CD-i 是一台短板不少的游戏主机,电源就是其中之一。不知何故,工程团队决定让它使用与以太网相同的 8P8C(RJ45)连接器。于是就像你的网线一样,那个卡扣老是会折断。MattKC 很想知道 CD-i 能否受益于 USB 供电升级,并着手把想法变成现实。
计划本身很简单——让 CD-i 改用 USB-C 供电,摆脱随机附赠的笨重原装电源。鉴于这台主机几乎完全靠 5V 运行,本该相当容易。只是原版规格里有个小细节让事情变难了一点:主机设计为从 5V 线路取电最高 3A,同时还需要一条 0.2A 的 -5V 线路。若不是这条负电压线路,随便找个输出 5V 的 15W USB-C 充电器就能带动机器。而这条额外的负线让事情复杂起来——负电压固然可以用一些辅助电路生成,但多数充电器很难再挤出那点额外功率。市面上虽然不缺大功率 USB-C 充电器,但多数是靠提升电压来输出更大功率,5V 输出普遍封顶 3A。
因此有必要多花点功夫。MattKC 决定做一块板子,先与 USB-C 充电器协商取 9V 以获得足够功率预算,再降压到 5V,同时用一级反相电路生成 -5V。其中 CH221K 芯片负责协商 9V USB-C 供电,TPSM84538 把电压降到 5V 并提供最高 5A 输出,LT3580 则负责把电压反相成 -5V。板上还有电源切换电路,因为原装电源砖里本就内置了这部分功能。

如果你有一台 CD-i、已经受够了跟原装电源较劲,这会是个很棒的升级。我们过去也详细探讨过 USB 供电(USB PD),需要补课的话可以参考。
本文来源:https://hackaday.com/2026/10/23/running-a-philips-cd-i-off-usb-c/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
The Philips CD-i is a console with many shortcomings, and those include the power supply. For whatever reason, the engineering team decided it should use an 8P8C connector just like Ethernet. Thus, just like your Ethernet cables, it has that annoying problem of the tab snapping off all the time. [MattKC] wondered if the CD-i could benefit from a USB power upgrade instead, and set about making it a reality.
The plan was simple enough—get the CD-i running off of USB-C instead of the ungainly original power supply that shipped with the unit. Given the console runs almost exclusively off of 5 V power, it should have been pretty easy. Only, the original spec adds one little detail that makes things a bit harder. The console is designed to draw up to 3 A from the 5 V line, while also having a -5 V line at 0.2 A. If not for that negative supply, it would have been easy to run the unit off any old 15 W USB-C charger spitting out 5 V. That extra negative line complicates things, because while the negative line could be created with some supporting electronics, it’s hard to find that extra watt from most chargers. While there are plenty of higher-wattage USB-C chargers, the majority tend to use higher voltages to deliver the additional power, capping the 5 V output at 3 amps.
Thus, it was necessary to work a little harder. [MattKC] decided to build a board that would negotiate with a USB-C charger for 9 V operation to get the power budget necessary. This would then be stepped down to 5 V, while there would also be an inversion step to supply the -5 V line, too. A CH221K chip does the job of negotiating a 9 V USB-C power supply, while a TPSM84538 steps the voltage down to 5 V with the capacity to supply up to 5 A. An LT3580 chip then inverts this voltage for the 5 V line. There’s also a power switching circuit on board because the CD-i included some of that functionality in the original power brick.

If you’ve got a CD-i and you’re sick of fussing with the original power supply, this could be a great upgrade. We’ve also explored USB Power Delivery in detail before, if you need a primer.