
光伏电池听起来神秘,结构其实很简单:一块 p 型硅片,加上一层掺磷的 n 型层,就是一个 PN 结。正因为简单,在家用几样常见材料加一台窑炉就能做出可工作的太阳能电池。博主 Dr. Semiconductor 最新视频里用的不是电窑,而是一台微波窑,于是有了「用微波炉做太阳能电池」这个标题。
起点是一片网购的裸硅片,注意要买没有做过刻蚀、表面干净的片子。接着配制掺磷源:1 毫升正硅酸乙酯(TEOS)、0.3 毫升 85% 磷酸、5 毫升乙醇与 0.25 毫升蒸馏水,低温煮沸 30 分钟后,用旋涂台(视频里直接拿电脑风扇改装)均匀涂在切成方形的硅片上。
涂好后的硅片放进微波窑,再送入微波炉,以较低功率烘烤半小时。视频中实测微波功率必须低于 50%,否则硅片会被烧熔——微波窑升温很快,这一点需要格外小心。
出炉后把新形成的电池周边那层玻璃状薄膜用砂纸磨掉或化学腐蚀掉,露出干净区域。随后在 p 型硅一侧涂镓铟合金做电极,在刚掺杂的 n 型硅一侧压一小块铟,两个接触电极就位,电池即可输出电流。
成品实测转换效率约 5%。作者认为还有很大提升空间:改用洁净环境、增加减反射涂层、优化电极接触电阻,都能把效率往上推。完整的配方与视频里讨论的各类问题,也同步发布在其博客文章中。对于想做科普演示或带孩子动手的创客来说,这条路线门槛低、材料易得,是理解 PN 结与光伏效应的直观教具。
本文来源:https://hackaday.com/2026/10/19/making-photovoltaic-solar-cells-with-a-microwave/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
Although solar panels may seem like a kind of magic, they’re really quite simple devices, in their silicon form featuring nothing but the p-type silicon wafer and an n-type layer doped with e.g. phosphorus. Because of this simplicity it’s quite possible to make your own solar cells at home using only a few basic, off-the-shelf ingredients and a kiln, which in this recent video by [Dr. Semiconductor] uses a microwave kiln and thus justifies the video’s title.
Even the silicon wafer that you start with can be easily purchased online, though you have to be careful that it’s a bare wafer, without existing etchings on it. On this you need to get a phosphorus-rich layer, which is done by creating a delicious mixture of 1 mL of tetraethyl orthosilicate (TEOS), 0.3 mL of 85 wt% phosphoric acid, 5 mL of ethanol and 0.25 mL of distilled water. After low heat boiling this for 30 minutes, it is spincoated onto the cut square of silicon wafer using a spinning platform, like a PC fan.
Next, you shove the coated silicon into the kiln and put it into the microwave to bake at a fairly low power level for half an hour. In the video it took less than 50% power of the microwave to not melt the silicon, so remember that those microwave kilns get pretty hot.
With the delightful smells of freshly baked silicon now teasing your nostrils, you can then take out the doped silicon to sand or etch off the thin layer of glass that’s formed around the new PV cell. On the clear spots you can now put a gallium-indium contact on the p-type Si side and a wad of indium on the newly doped Si-P side, which are now your contacts for the PV cell.
The full recipe along with many of the issues discussed in the video can also be found on the blog article , though the video conclusion notes that many improvements are still possible. The created PV cell in the video reaches an efficiency of about 5%, but this could be improved through changes like the use of a clean-room, adding an anti-reflection coating and improving the contact with the cell.