
【产品开发】Hackaday 报道,工程师最重要的工具莫过于书写用具。Choronova Engineering 是一家对细节格外较真的团队,这次他们决定重新发明卷笔刀。
在团队眼中,理想的铅笔尖形状是凹锥形——用刀削很容易实现,但传统的旋转卷笔动作几乎不可能做到。那么,能不能把「刀削」的动作自动化?这其实是个古老的想法,最早的例子可追溯到 1910 年。在这一设计中,刀片沿两条特定曲率的轨道运动以形成凹锥,动力来自连接小型曲柄机构的凸轮轴。初步测试显示,该机构切出的形状符合预期,但缺少铅笔旋转机构。
受日内瓦轮(Geneva wheel)启发,Chronova 开发了一套全新的间歇机构来改善操作手感。与平面上两个齿轮状机构不同,其输入与输出可以呈 90 度错位布置,为刀片运动留出空间:旋转输入到称为「指度小齿轮」的零件,输出则连接到「灯笼齿轮」。
指度小齿轮每完整旋转一圈,会拨动灯笼齿轮两个齿。利用这一特性,只要灯笼齿轮采用奇数齿数,输出端就能获得两倍于输入的工位数;在齿轮旋转的其他位置,灯笼齿轮则保持锁定。铅笔通过弹簧夹头固定,并安装在连接灯笼齿轮旋转输出的丝杠上,每摇一圈曲柄,铅笔就略微向前送进一点。项目还配有削屑收集器与手柄,收尾相当利落。
成品运转良好,但作为一款实用的卷笔刀并不合格——削一支铅笔耗时且费力。不过,把简单任务过度工程化成一台有趣的机器,本身就是创客的乐趣所在。
本文来源:https://hackaday.com/2026/10/17/making-a-new-mechanism-for-a-reciprocating-pencil-sharpener/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
An engineer's greatest tool is the writing utensil. Be it pen or pencil, we use them for everything from making diagrams to marking out cuts. But as with any practitioner of an art, we can tend to become rather particular about the details. Choronva Engineering is not different, and to that end set out to re-invent the pencil sharpener.
In this case, Chronova's ideal pencil tip shape is a concave cone. This is a shape quite trivial to make by using a knife, but rather impossible with a traditional twisting motion. But what if one automatized the knife whittling motion? This is actually a very old idea, with examples dating back to at least 1910. In this example, the blade is guided along two tracks with a particular curvature to enable the concave cone. This is driven by a cam shaft connected to a little cranking mechanism. Initial tests showed the mechanism works quite well at producing a cutoff of the desired shape, but lacks a pencil rotation mechanism.
Inspired by the Geneva wheel, Chronova developed a fresh intermittent mechanism for improved satisfaction in the sharpener's operation. Instead of two gear-like mechanisms on a flat plane, the input and output can sit at a 90 degree offset from each other giving room for the blade's motion. Rotation is input on a part called the indexing pinion which outputs on a lantern pinion.

At every full rotation of the indexing pinion, it interfaces with the lantern pinion moving it two teeth. Because of this quirk, by making the lantern with an odd number of teeth, twice the number of indexing positions are available in the output. At all other points in the pinion's rotation the lantern is locked in place.
The pencil is held in place with a collect chuck and mounted on a screw coupled to the lantern pinion's rotational output. This enables the pencil to move forward slightly with every turn of the crank. The project is topped of neatly with a shavings catcher and handle.
It works rather well, but a practical pencil sharpener that does not make. It takes a rather long time, and is fairly laborious to use. But over-engineering machines to do simple tasks is still quite fun.