
【产品开发】Hackaday 报道,电子元件越做越小,显微镜已成为精细作业中越来越不可或缺的工具。但在检查电子焊点时,单纯的俯视视角往往不够用,一位名叫 Corebb 的创客为此打造了一台带侧视旋转视角的显微镜。
这台显微镜由商用 C 口显微镜镜头组件和 USB 相机构成,镜头可变放大倍率最高达 200 倍,对电子维修来说绰绰有余,并安装在可调支架上以移动焦点位置。系统还配有一圈 LED 环形灯用于照明,以及两片偏振滤光片——一片装在镜头上、一片装在灯环上。当两者调整为互相垂直 90 度时,可以消除反光表面的眩光。
为了实现侧视,Corebb 制作了一个快装转接件:用一对反射镜从物体侧面捕获画面,并导入主显微镜镜头;额外的一片凹透镜用于补偿加长的光路,滚珠轴承则让整个转接件围绕显微镜旋转,从任意角度捕捉被观察物体。
创客最初尝试用 3D 打印制作转接件,但发现形变导致的抖动难以接受;改为机加工铝件后不仅更坚固,更细的支撑结构还减少了阴影。转接件通过小磁铁吸附在显微镜上,可保持光路持续对齐。
这并非人们第一次给焊接显微镜加装侧视视角,但这台 DIY 方案看起来要实惠得多。如果想给自己的显微镜加装偏振光源,Hackaday 此前也有过相关教程。
本文来源:https://hackaday.com/2026/10/18/building-a-microscope-with-a-3d-view/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
As electronic components grow ever smaller, a microscope has become an increasingly indispensable tool for any fine work; when inspecting electronics, though, especially solder joints, Corebb found a top-down view too limiting, so he built his own microscope with a rotating side-angle view.
The microscope itself is made of a commercial C-mount microscope lens assembly and a USB camera; the lens has a variable magnification factor up to 200x, which is plenty for electronics work, and is mounted on an adjustable stand to move the focal point. This is paired with an LED ring for illumination and two polarizing filters, one mounted on the lens and one one the lighting ring; when adjusted to 90 degrees from each other, these eliminate glare from reflective surfaces.

To view subjects from the side, Corebb built a snap-on adapter. This uses a pair of mirrors to capture a view from the side of the object and direct this through the main microscope lens. An additional concave lens compensates for the increased length of the optical path, and ball bearings let the whole adapter rotate around the microscope and capture the subject from any angle. Corebb tried 3D-printing the adapter, but found that flexing caused too much jitter; in addition to being sturdier, a machined aluminium part reduced shadows by allowing for thinner supports. The adapter snaps onto the microscope with small magnets, which keep the optical path consistently aligned.
This isn't the first time we've seen a soldering microscope with a view from the side, but this does look much more affordable. If you'd like to try the polarized light source with your microscope, we've covered that before.