
1. 从废品到宝藏:SES电子价签的二次生命
第一次看到SES电子价签是在一家即将倒闭的超市里,成堆的废弃价签被当作垃圾处理。当时我就想:这些自带墨水屏的小玩意,能不能变废为宝?后来在二手平台以每片不到20元的价格收购了一批2.66寸和4.2寸的三色墨水屏,开启了我的改造之旅。
这些价签原本的设计寿命是3-5年,但实际使用中往往因为电池耗尽或系统升级就被淘汰。拆开外壳会发现,内部的核心部件——墨水屏依然完好。经过测试,这些屏幕在断电后仍能保持最后显示的内容长达半年之久,这简直就是为低功耗信息展示量身定制的特性。
硬件规格解密:
· 2.66寸型号采用SE2266FS092屏幕+GL340主控
· 4.2寸型号使用SE2417FS051屏幕+AX8052F143主控
· 统一采用24pin 0.5mm间距FPC接口
原装主控芯片的局限性很明显:缺乏无线通信模块,只能通过专用设备有线更新内容。这也是商业场景淘汰它们的主要原因,但对于DIYer来说,这恰恰是改造的突破口。我实测发现,这些屏幕的对比度能达到15:1,在环境光下阅读体验堪比纸质,完全能满足信息展示的需求。
2. 硬件改造:从零设计ESP32驱动板
原装驱动板最大的问题是通信方式单一,要让它智能化必须"换脑"。ESP32-C3成了我的首选,它不仅支持Wi-Fi和蓝牙双模通信,价格还控制在10元以内。但市面上适配这类墨水屏的驱动板要么缺货要么昂贵,比如微雪的同类产品价格是屏幕本身的2-3倍。
自制驱动板的关键设计要点:
· 电源管理:需要3.3V和-15V双电压输出,负压用电荷泵方案实现
· 接口转换:24pin FPC座子要选用0.5mm间距的翻盖式连接器
· 信号隔离:SPI总线需添加74HC125缓冲器保护ESP32 GPIO
· 状态检测:BUSY引脚必须设计分压电路,避免电平不匹配
在立创EDA上设计时,我参考了Pervasive Displays官网的参考电路,但做了三处关键改进:增加了ESD保护二极管、优化了电源滤波网络、将测试点改为邮票孔。打样5片板子总共花费不到50元,焊接时最麻烦的是FPC座子,建议使用热风枪辅助焊接,完成后一定要用万用表测试各引脚间是否短路。
3. 固件开发:破解墨水屏的通信协议
移植驱动时遇到的第一个坑是寄存器配置。与常见的UC8151驱动芯片不同,这些价签屏幕使用定制指令集。通过逻辑分析仪抓取原装主控的通信数据,我发现两个关键差异:
· 软复位命令不是标准的0x12,而是向0x00寄存器写入0x0E
· 温度补偿参数必须配置为0x19,否则会出现刷新残影
SPI驱动核心代码框架:
void epd_init() { // 硬件复位 gpio_set_level(RST_PIN, 0); vTaskDelay(50); gpio_set_level(RST_PIN, 1); // 发送初始化序列 send_command(0x00); send_data(0xCF); // 面板设置 send_command(0xE5); send_data(0x19); // 温度校准 } void update_screen(uint8_t *buffer) { send_command(0x10); // 黑白数据 for(int i=0; i 特别要注意BUSY信号的电平逻辑,这两款屏幕都是低电平表示忙状态,与常见设计相反。我在调试时曾因此卡住两天,后来用示波器捕获信号波形才发现问题。建议在代码中加入超时机制,避免死等: void wait_busy(int timeout_ms) { int waited = 0; while(gpio_get_level(BUSY_PIN) == 0) { vTaskDelay(10); waited += 10; if(waited > timeout_ms) break; } } 直接使用微雪的官方APP虽然方便,但存在两个痛点:传输速度慢(约30秒/张)、无法保存历史图片。于是我基于ESP32的SPP协议开发了定制方案,关键优化点包括: · 图像预处理:在手机端先将图片转为1bit位图,尺寸匹配屏幕分辨率 · 数据压缩:使用简单的游程编码(RLE),实测压缩率可达60% · 校验重传:每512字节数据包增加CRC校验,错误自动重传 Android端关键代码逻辑: void sendImageToDisplay(Bitmap image) { Bitmap bwImage = convertTo1Bit(image); // 二值化处理 byte[] rleData = RLE.encode(bwImage); // 游程编码 OutputStream out = socket.getOutputStream(); int packetSize = 512; for(int i=0; i 实测将4.2寸屏幕的传输时间从原来的35秒缩短到12秒。更惊喜的是,这个方案在ESP32上仅占用12KB RAM,剩余资源足够跑个WebServer实现HTTP接口控制。 墨水屏本身不耗电,但无线模块是吃电大户。我的解决方案是: · 采用TPS61099升压芯片,效率达93% · 添加HT7333 LDO为ESP32提供稳定3.3V · 设计自动休眠机制:无操作10分钟后进入深度睡眠 功耗实测数据:工作模式电流消耗持续时间刷新屏幕120mA15秒蓝牙传输中85mA12秒待机状态1.2mA持续深度睡眠18μA持续 使用2000mAh的锂电池理论上可支持约3个月的持续展示,如果每天刷新2次,续航能延长到1年以上。我在驱动板上预留了太阳能充电接口,配合6V/2W的太阳能板就能实现永久续航。 这个项目最让我自豪的实际应用,是给开餐馆的朋友做的智能菜谱牌。将4.2寸屏幕嵌入亚克力相框,通过蓝牙每天更新特价菜: · 厨房电脑运行定时任务,生成当日菜单图片 · 通过Python脚本自动传输到各个屏幕 · 屏幕只在收到新内容时唤醒刷新 def update_menu(device_mac, image_path): img = Image.open(image_path).convert('1') # 转为黑白 img = img.resize((400, 300)) # 匹配屏幕分辨率 with BluetoothSocket(RFCOMM) as sock: sock.connect((device_mac, 1)) sock.send(convert_to_1bit(img.tobytes())) time.sleep(15) # 等待刷新完成 朋友反馈说,这套系统比传统纸质菜单节省了90%的印刷成本,而且随时能调整内容。最意外的是,有顾客专门为了看屏幕上的每日手绘菜单而来消费。 在社区分享这个项目后,我收集到一些典型问题,这里集中解答: Q1:屏幕刷新后出现鬼影怎么办?A:这是墨水屏的通病,建议在每次刷新前先全屏写入白色,再发送新数据。温度也会影响效果,25℃时表现最佳,可以适当调整0xE5寄存器的值。 Q2:FPC排线容易松动脱落A:除了选用质量好的连接器,我发现在排线末端贴一小块双面胶能大幅提高可靠性。也可以用热熔胶固定,但要避免胶渗入接触点。 Q3:想显示更多颜色A:三色屏的红黑白是通过分帧刷新实现的。先发送黑色数据刷新,保持电压再发送红色数据,最后用白色覆盖不需要显色的区域。时序控制很关键,不同批次屏幕可能需要调整延迟参数。4. 蓝牙图像传输方案优化
5. 电源管理与续航优化
6. 实战案例:智能菜谱展示器
7. 常见问题与解决方案
本文来源:http://www.mfbz.cn/news/326956
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
The first time I saw the SES electronic price tag was in a supermarket that was about to close down, and piles of discarded price tags were treated as garbage. At that time, I was wondering: can these gadgets with ink screens turn waste into treasure? Later, I bought a batch of 2.66 -inch and 4.2-inch three-color ink screens for less than 20 yuan per piece on the second-hand platform, which started my transformation journey.
The original design life of these price tags is 3-5 years, but in actual use they are often eliminated due to battery depletion or system upgrades. You will find that the ink screen, the core component of the interior, is still intact. After testing, these screens can retain the last displayed content for up to half a year after the power is turned off, which is simply a tailored feature for low-power information display.
Hardware decryption:
· 2.66 inch model uses SE2266FS092 screen + GL340 master
· 4.2 inch model uses SE2417FS051 screen + AX8052F143 master
· Unified 24pin 0.5mm spacing FPC interface
The limitations of the original main control chip are obvious: there is a lack of wireless communication modules, and content can only be updated via a dedicated device wired. This is also the main reason why business scenarios eliminate them, but for DIYers, this is exactly the breakthrough of transformation. I found that these screens can achieve a contrast ratio of 15: 1, and the reading experience in ambient light is comparable to paper, which can fully meet the needs of information display.
The biggest problem with the original drive board is that it has a single communication method. To make it intelligent, you must "change your brain". The ESP32-C3 became my first choice, not only supporting Wi-Fi and Bluetooth dual-mode communication, but also controlling the price within 10 yuan. But the drive boards that fit this kind of ink screen on the market are either out of stock or expensive, for example, the price of similar products such as snow is 2-3 times that of the screen itself.
Key design points of the homemade drive board:
· Power management: 3.3V and -15V dual voltage outputs are required, and the negative voltage is realized by the charge pump scheme
· Interface conversion: 24pin FPC seat to use 0.5mm pitch clamshell connector
· Signal Isolation: Add 74HC125 buffer to SPI bus to protect ESP32 GPIO
· Condition detection: Busy pins must be designed with voltage dividing circuits to avoid level mismatches
When designing the EDA, I referred to the reference circuit on the Pervasive Displays website, but made three key improvements: adding an ESD protection diode, optimizing the power filter network, and changing the test point to a stamp hole. Proofing 5 plates cost less than 50 yuan in total. The most troublesome part when welding is the FPC seat. It is recommended to use a hot air gun to assist in welding. After completion, be sure to use a multimeter to test whether the pins are short-circuited.
The first pit encountered when porting the driver is the register configuration. Unlike common UC8151 driver chips, these price tag screens use a custom instruction set. Grabbing the communication data of the original main control through the logic analyzer, I found two key differences:
· The soft reset command is not a standard 0x12, but instead writes 0x0E to the 0x00 register
· The temperature compensation parameter must be configured to 0x19, otherwise a refresh shadow will appear
SPI Driven Core Code Framework:
void epd_init () {//hardware reset gpio_set_level (RST_pin, 0); vTaskDelay (50); gpio_set_level (RST_pin, 1);//send_command (0x00); send_data (0xCF);//panel set send_command (0xE5); send_data (0x19);//temperature calibration} void update_screen (uint8_t * buffer) {send_command (0x10);//black and white data for (int i = 0; i < buffer_size; i + +) {send_data (buffer [i]);}_send command (0x12);//refresh instruction wait_busy (15000);//wait up to 15 seconds}
Pay special attention to the level logic of the busy signal, both screens are low to indicate a busy state, contrary to the common design. I was stuck for two days during debugging, and later discovered the problem by capturing the signal waveform with an oscilloscope. It is recommended to add a timeout mechanism to the code to avoid death and so on:
void wait_busy(int timeout_ms) { int waited = 0; while(gpio_get_level(BUSY_PIN) == 0) { vTaskDelay(10); waited += 10; if(waited > timeout_ms) break; } }
Although it is convenient to directly use the official app of Mild Snow, there are two pain points: the transmission speed is slow (about 30 seconds/piece) and the historical pictures cannot be saved. So I developed a customized solution based on the spp protocol of ESP32. Key optimization points include:
· Image preprocessing: first convert the picture to 1bit bitmap on the mobile phone, the size matches the screen resolution

· Data compression: Using simple RLE, the measured compression rate is up to 60%
· Verification retransmission: CRC verification is added every 512 bytes of data packet, error automatic retransmission
Android Key Code Logic:
void sendImageToDisplay (Bitmap image) {Bitmap bwImage = convertTo1Bit (image);//binarization byte [] rleData = RLE.encode (bwImage);//run encoding OutputStream out = socket.getOutputStream (); int packetSize = 512; for (int i = 0; i < rleData.length; i + = packetSize) {byte [] chunk = Arrays.copyOfRange (rleData, i, Math.min (i + packetSize, rleData.length)); out.write (chunk); out .flush ();//wait for device confirmation (! waitAck ()) {retryPetack (i);}}
The actual test reduced the transmission time of the 4.2-inch screen from the original 35 seconds to 12 seconds. Even more surprising is that this solution only occupies 12KB of RAM on the ESP32, and the remaining resources are enough to run a WebServer to achieve HTTP interface control.
The ink screen itself does not consume power, but the wireless module is a large consumer of electricity. My solution is:
· 93% efficiency with TPS61099 boost chip
· Add HT7333 LDO to provide stable 3.3V for ESP32
· Design an automatic sleep mechanism: enter deep sleep after 10 minutes of inactivity
Power consumption actual measured data: operating mode current consumption duration refresh screen 120mA 15 seconds Bluetooth transmission 85mA 12 seconds standby state 1.2mA continuous deep sleep 18μA continuous
Lithium batteries with 2000mAh can theoretically support continuous display for about 3 months, and if refreshed 2 times a day, the battery life can be extended to more than 1 year. I reserved the solar charging interface on the drive board, and with the 6V/2W solar panel, I can achieve permanent battery life.
The practical application of this project that I am most proud of is the smart recipe card for friends who open restaurants. Embed the 4.2-inch screen in the acrylic photo frame and update the specials every day through Bluetooth:
· The kitchen computer runs a timed task to generate a menu picture of the day
· Automatic transfer to individual screens via Python scripts
· The screen only wakes up to refresh when new content is received
def update_menu (device_mac, image_path): img = Image.open (image_path) .convert ('1') # Go black and white img = img.resize ((400, 300)) # Match screen resolution with BluetoothSocket (RFCOMM) as sock: sock.connect ((device_mac, 1)) sock.send (convert_to_1bit (img.tobytes ()) time.sleep (15) # Wait for refresh to complete
Friends report that the system saves 90% of the cost of printing compared to traditional paper menus, and can adjust the content at any time. Most unexpectedly, there are customers who spend exclusively to look at the daily hand-drawn menu on the screen.
After sharing this project with the community, I gathered some typical questions and focused on answering them here:
Q1: What if a ghost appears after the screen refreshes? A: This is a common problem with ink screens. It is recommended to write white in full screen before each refresh before sending new data. Temperature also affects the effect, the best performance at 25°C, the value of the 0xE5 register can be adjusted appropriately.
Q2: FPC cable is easy to loosen and fall off A: In addition to using good quality connectors, I found that attaching a small piece of double-sided adhesive at the end of the cable can greatly improve reliability. It can also be fixed with hot melt adhesive, but avoid penetration of the adhesive into the contact points.
Q3: Want to display more colors A: The red, black and white of the three-color screen is achieved by refreshing in frames. Send the black data refresh first, keep the voltage and then send the red data, and finally cover the areas that do not need to be colored with white. Timing control is critical and different batches of screens may require adjustment of delay parameters.
This article is from: http://www.mfbz.cn/news/326956 For copyright issues, please write to: 13951431913#139.com or submit a review on the right.