
过去几周硬件黑客圈最激动人心的消息,莫过于乐鑫 ESP32 微控制器的 Wi-Fi 无线电中被解锁出隐藏 SDR 功能,可作收发两用。不过有一个遗憾:尽管外界曾猜测它们或许能下探到更低频率,但目前被证实可用的只有 Wi-Fi 频段附近——按 2.4 GHz 元件计,大约是 2.4 至 2.5 GHz 的 100 MHz 切片,或许能下探到 1.8 GHz。如果想让它工作在其他频段,是时候请出变频器这个老而可靠的办法了。
变频器的原理来自模拟接收机:两个频率混频后,输出频谱中同时包含它们的和频与差频。老式收音机、电视机的调谐旋钮正是依靠这一机制。具体做法是把天线收到的频率范围与一个固定振荡器的输出混频,令其差频恰好落入你的无线电工作频段,这样调谐你的电台就等于调谐整个天线频段。举例来说,若 ESP32 接收 2.4 至 2.5 GHz,输入端的混频器配一个 2 GHz 本振,就能让 ESP32 的接收机收到 400 至 500 MHz 频段。实际电路需要在输入输出两侧加滤波器阻挡带外信号,但原理就是这么简单。妥善处理功率与放大后,它同样适用于发射,此时设备称为“变频收发机”。
要做一个实用的接收变频器,需要输入滤波器、混频器、输出滤波器和本振。滤波器常用现成件,价格不高;混频器可以简单到用一颗高速肖特基二极管;本振甚至可以用另一颗 ESP32——它现在就能当 SDR 发射机用,而且便宜到只需一两美元。输入滤波器通常是低通型,最常见的“π 网络”由信号通路上的一个电感和两侧对地电容组成,数值可自行计算或借助在线计算器。输出滤波器要尽量抑制本振频率、通过 ESP32 接收频段,Wi-Fi 行业正好有大量现成产品可选,贸泽、Digi-Key 上都能便宜买到。
文章最后还给出了发射注意事项:ESP32 虽不大也可能损坏或过载为接收设计的器件,因此要么选用耐发射的器件,要么把功率压低后在较低频率上再放大。作者强调,以上并非拿来即用的完整设计,但足以给你足够的指路牌。RTL-SDR 玩家们早就攒下大量变频器制作经验,直接借鉴即可。
本文来源:https://hackaday.com/2026/10/15/so-you-want-to-make-your-sdr-work-on-other-frequencies/
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
Perhaps the most exciting news of the past few weeks in the world of hardware hacking has been the unlocking of hidden SDR functionality in the Wi-Fi radios found on Espressif ESP32 microcontrollers. They can be used as both transmit and receive SDRs, and given that it is early days for this hack we expect that great things are yet to come.
There is one snag though, despite speculation that they might be dragged down to much lower frequencies, as far as we know they are only proven to work around the Wi-Fi frequencies. Though the reality may be wider we will take that for a 2.4 GHz part as a 100 MHz slice from 2.4 GHz to 2.5 GHz. Plenty of possibilities there, and they might even work down to 1.8 GHz, but there would be so much more to do if it could work elsewhere in the spectrum. So it is time to look at the converter, a tried and tested old way to make a radio work on a different frequency.

A converter uses exactly the mixing principle. The antenna frequency range is mixed with the output of a fixed oscillator whose frequency is chosen so that their difference represents the frequency band of your radio. Thus tuning your radio tunes across the output of your mixer, which is the same as tuning across the antenna frequency range. For a numerical example, if the ESP32 receives from 2.4 GHz to 2.5 GHz, a mixer on its input with a 2 GHz local oscillator would allow the ESP32's receiver to pick up the 400 MHz to 500 MHz band. In practice the circuit requires filters for both input and output to keep out-of-band stuff from going where it should not, but it really is that simple. Best of all, with appropriate handling of power and amplification, it works for transmitters too, and such a device is called a transverter.
To make a practical converter then, we need an input filter, a mixer, an output filter, and a local oscillator. The filters are often off-the-shelf parts and need not be too expensive, the mixer can be as simple as a fast Schottky diode, and the local oscillator could even in this case be another ESP32. The input filter is usually a low-pass filter, most commonly a Pi network with an inductor in the signal path and a capacitor to ground on either side. The output filter needs to reject the local oscillator frequency and pass the ESP32 receive range, and here the Wi-Fi industry offers exactly those filters cheaply from distributors such as Mouser or Digi-Key.
The same technique works for shifting the ESP32's transmit output down to the desired frequency, but there is a catch. Even the modest output from an ESP32 can be enough to damage or overload parts designed for receivers, so you have two choices: pick transmit-appropriate parts, or dial back the power to a low level, and amplify it at the lower frequency.