大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?


AI free token/AI免费积分

又一家汽车媒体的测试上热搜了。

昨晚,汽车之家找来了三辆纯电轿车,在北京环线上跑了一场高速挑战。结果一出,网上一片哗然。

一辆官方标称电池续航 1008 公里的行政轿车,只撑了 566.4 公里,电池续航达成率刚刚过半,只有 56.2%,表显能耗为 15.1kWh/100km。另外两辆轿车表现稍好,达成率分别是 63.6% 和 75.3%,跑得最远的那台做到了 678.6 公里。

一千公里的电池续航被打了个对折,评论区自然少不了各种冷嘲热讽。

就在键盘车神们争得不可开交的时候,宝马在沈阳搞了一场创新日活动,顺手晒出了一份成绩单:

一辆新世代 BMW i3 从沈阳往返大连,完成了 1213 公里全程不充电挑战,电池续航达成率冲到了 118%。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

但要说明的是,宝马这场测试并不像汽车之家那样全程跑高速,也有大量的国道和城市路段,真要把新世代 i3 放到同一场测试里,它的电池续航恐怕也得缩水。

不过这并不意味着这个成绩毫无意义,真正让我觉得宝马有点东西的,是它跑出来的百公里平均电耗——只有 8.8kWh。

在同级别的量产车里,这是一个史无前例的成绩。

大电池和低能耗,并不冲突

众所周知 ,想要做长电池续航,最笨也是最省事的办法就是堆电池。雷军在今年公开受访时坦言,小米汽车在这维度确实要向特斯拉学习,把能耗做低一些。

不过,宝马能做到上千电池续航,同样离不开一块大电池——新世代 i3 的电池容量达到了 113.4kWh。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

但和特斯拉的「小电池低能耗」思路不同,宝马的想法是:把电池做大的同时,能耗也要低。

新世代 i3 能做到个位数的能耗,最大功臣是刚刚在沈阳工厂下线的第六代动力电池,这也是大圆柱电池第一次在一线豪华品牌里挑起大梁。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

华晨宝马总裁宝思齐在活动现场表示,第六代动力电池在沈阳量产,是新世代车型在华落地的关键。宝马纯电车型的命脉,就在这根圆柱上了。

宝马使用的 46 系列大圆柱电池,实际上并不是什么新东西,在此之前,动力电池行业就已经针对圆柱电芯的尺寸摸索了十几年。从特斯拉 Model S 的 18650,到后来 Model 3 换用的 21700,再到今天的 46 系列,圆柱电池在这些年里越长越「胖」。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

但各位发现没有,自从特斯拉在 2020 年的电池日发布了 4680 电芯之后,圆柱电芯的直径就没有再变大了。

这是为什么?

早期的 18650 单体容量只有 2-3Ah,一台车要塞进好几千节电池。例如早期 Model S 的电池包里就有 7000 多节 18650,光是这几千个钢壳的重量就格外感人,质量能量密度谈不上体面,想要有所提高,就必须要把电池做粗。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

但这个圆柱做得太粗也不行,电芯中间不好散热,可能会导致老化加速甚至发生热失控。

据特斯拉当年公布的热力学模型测算,46 毫米恰好是兼顾电池续航和热管理的物理临界点。

最先将 46 毫米大圆柱投入量产的正是特斯拉,他们在 2020 年发布后,很快将其应用在了得州工厂下线的 Model Y 和 Cybertruck 上。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

不过,受制于当时的制造工艺,大圆柱在快充和散热上还并不完美,真正救活大圆柱的,实际上是一项叫做「全极耳」的工艺。

以往的电芯只有一两个极耳,电子得在长达几十厘米的金属箔片上横向跋涉。大电流一过,高阻抗会让电芯迅速发烫,这也是早期大圆柱电池不敢碰大功率快充的原因。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

全极耳的做法是,将极片边缘做成一整块导电端面,让电子顺着极短的路径直接流出。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

上面这一段倒也不用细读,你只需要知道,这一结构调整,把电芯内阻降低了 80%,电芯在充放电时的产热大幅缩减。

正是因为产热降下来了,电芯有了更高的热安全上限。有了这层保障,工程师才敢在内部导入更活跃的电化学体系。

这也是为什么宝马可以在第六代电芯上,直接应用 90% 以上的高镍正极和硅碳负极。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

硅材料的比容量极高,但吸饱锂离子后膨胀得像个气球。方壳电池如果用高比例硅负极,壳体极易被撑变形导致析锂。

而圆柱钢壳具备天然的轴对称结构,具备很强的环向机械刚度,可以均匀地约束硅负极在充放电过程中的形变。

为了兼顾不同车型,宝马还准备了两种规格的圆柱电池:高 95 毫米的 4695 留给轿车,降低底盘厚度;高 120 毫米的 46120 留给 SUV,提高电池容量。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

宝马没有像特斯拉那样搞激进的自研自产,而是自己制定配方标准,生产这件事则交由中国供应商来完成——宁德时代和亿纬锂能。

正是因为有了成熟的制造体系,沈阳工厂 100 亿元的电池项目才能迅速落地,赶在新世代全面铺开前完成了硬件储备。

大圆柱电池是好东西,但人们为什么不用?

不知道你们有没有遇到过这样的情况,车速一到 120km/h,空调很快就不凉了。我的特斯拉 Model 3 就是这样,每次都得手动把空调调低两度,车里才能稍微有点凉意。

这实际上就是电池的高温保护。按照 Model 3 的风阻和滚阻数据推算,车辆在 120km/h 巡航时,电池需要持续保持 18 到 20kW 的输出。

依据焦耳定律,导体发热量和电流平方成正比,持续高功率放电会让电芯内部快速积热。偏偏动力电池对工作温度格外挑剔,电芯温度一旦过高,热管理平台就会把散热优先级给到电池。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

特斯拉这套集成热管理平台的核心部件是八通阀,遇到电芯过热,八通阀会切换冷媒与冷却液的流向,将压缩机产出的大部分制冷量,借助板式换热器直接抽调给电池水冷回路。

而 Model 3 的压缩机最大制冷功率总共也就三四千瓦,被电池截走大半之后,空调自然就不够凉了。

大圆柱电池刚好应对了这个难题。

由于电芯的内阻降低了八成,放电过程产生的焦耳热便会大幅减少,常规水冷循环就足以维持正常温度,不用再和座舱抢制冷。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

除了高速空调的难题,后排坐姿也是纯电轿车被长期吐槽的地方。

算上液冷板和保护盖板,传统方壳电池的整包厚度普遍在 140 毫米上下。为了在底盘容纳这块电池,很多轿车座舱地板要被抬高两三公分,后排乘客坐大腿缺乏承托,长途坐久了自然会不舒服。

方壳电池之所以这么厚,就是因为电芯本身强度偏弱,电池包内部必须穿插厚重的横梁和框架来做物理防护。

而 46 系列大圆柱钢壳有着极强的抗压能力,可以直接作为底盘受力结构。宝马把它融入车身一体化后,电池包厚度减少了将近 20 毫米。

底盘变薄了,轿车也终于找回了传统燃油车那种舒展的贴地坐姿。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

还有一个难题,既然大圆柱电池的感受长处显著,国内动力电池大厂为什么没有转型?关键还是在于成本。

当下国内市面挑大梁的是磷酸铁锂,占了近七成装车份额。方壳做成 CTP 之后,电池包的体积利用率能超过 70%。而圆柱电芯之间天然存在无法消除的三角缝隙,空间利用率通常只有 60% 左右。把本身能量密度有限的铁锂做成圆柱,会白白浪费底盘容积。

另一维度,国内动力电池企业过去几年建起了数百 GWh 的方壳产能,把电芯制造成本压到了每瓦时 0.3 到 0.4 元的水平。在激烈的市面竞争下,企业很难再花一大笔钱推倒重来。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

而且即便强如特斯拉,也在 4680 电池上摔过跟头。

当年为了达成降本 56%,特斯拉挑选死磕干法正极工艺。但由于极片在压实过程中容易脆裂脱落,早期良品率长期停留在 70% 到 80% 之间,很难达到成熟产线 95% 以上的盈亏平衡点,Cybertruck 的产能爬坡也因而延误了很长时间。

宝马挑选了一条更取巧的路径,他们避开了尚未成熟的干法工艺,依靠高速湿法工艺达成量产。

这种挑选当然有代价。湿法工艺离不开溶剂涂布和高温烘烤产线,厂房占地大,耗电量也大,依靠干法正极降低制造成本的理论红利,宝马显然享受不到。

但豪华品牌的定价足以消化这些开支,相比于追求极致降本,宝马当下更需要的是量产节奏的确定性。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

另一维度,德国本土有着大量不限速高速公路,车辆在 160km/h 甚至更高时速下长途行驶,放电功率往往达到四五十千瓦,大圆柱低内阻与轴向散热的物理特性更合适这种高负荷工况。

如今,扫清了电池的工程阻碍,宝马的新车节奏显著紧凑了起来。

大电池+低能耗!宝马新世代 i3 跑了 1213 公里 百公里能耗只有 8.8 度?

按照宝马的规划,到 2027 年,中国市面会迎来近 20 款用上新世代工艺的新车。另外,宝马还打算在 2030 年把国产车型的比例拉高到 95% 以上,并把「中国制造」的宝马销至海外。

过去几年,人们买电车总会盯着车机和智驾,但随着机型和市面不断成熟,纯电车型的竞争终究会回归到底盘、热管理和能耗这些朴素的地方。

本文来源:https://www.ifanr.com/1684510
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。

Another car media test was hotly searched.

Last night, the car house found three pure electric cars and ran a high-speed challenge on the Beijing Loop Line. As a result, there was an uproar on the Internet.

An executive car with an official rated battery life of 1008 kilometers only lasted 566.4 kilometers, and the battery life achievement rate was just over half, only 56.2%, and the energy consumption was displayed at 15.1kWh/100km. The other two cars performed slightly better, achieving 63.6% and 75.3%, respectively, and the one that ran farthest achieved 678.6 kilometers.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

A thousand kilometers of battery life was folded in half, and the comment area was naturally full of cynicism.

Just when the keyboard gods were struggling, BMW organized an innovation day event in Shenyang and handed out a transcript:

A new-generation BMW i3 travels from Shenyang to Dalian and back, completing the 1,213-kilometer non-charging challenge, and the battery life achievement rate has risen to 118%.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

However, it should be noted that this test of BMW is not as fast as the car home. There are also a large number of national highways and urban roads. It is really necessary to put the new generation i3 into the same test, and its battery life may have to shrink.

However, this does not mean that this result is meaningless. What really makes me feel that BMW has something is that it runs out of the average power consumption of 100 kilometers - only 8.8kWh.

This is an unprecedented achievement in the same class of production vehicles.

As we all know, the dumbest and most convenient way to do long battery life is to stack batteries. Lei Jun admitted in a public interview this year that Xiaomi Cars does have to learn from Tesla in this dimension to lower its energy consumption.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

However, BMW can achieve thousands of battery life, and it is also inseparable from a large battery - the battery capacity of the new generation i3 reaches 113.4kWh.

But unlike Tesla's "small battery low energy consumption" idea, BMW's idea is: to make the battery larger, but also low energy consumption.

The new generation i3 can achieve single-digit energy consumption. The biggest contributor is the sixth generation of power batteries that have just been launched in the Shenyang factory. This is also the first time that a large cylindrical battery has provoked a big beam in a first-line luxury brand.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

BMW Brilliance President Bao Siqi said at the event that the mass production of sixth-generation power batteries in Shenyang is the key to the landing of new-generation models in China. The lifeblood of the BMW pure electric model is on this cylinder.

The 46 series of large cylindrical batteries used by BMW are actually nothing new. Before that, the power battery industry had been exploring the size of cylindrical batteries for more than a decade. From the Tesla Model S 18650, to the later Model 3 21700, to today's 46 series, cylindrical batteries have grown fatter over the years.

But you found that since Tesla released the 4680 cell on Battery Day in 2020, the diameter of the cylindrical cell has not grown any larger.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

Why?

The early 18650 had a monomer capacity of only 2-3Ah, and a car fort was stuffed with thousands of batteries. For example, there are more than 7,000 18650 sections in the battery pack of the early Model S. The weight of these thousands of steel shells alone is particularly touching. The mass energy density is not decent. If you want to improve it, you must make the battery thick.

However, this cylinder is too thick, and the heat dissipation in the middle of the battery cell is not good, which may lead to accelerated aging and even thermal runaway.

According to Tesla's thermodynamic model released that year, 46mm is just the physical tipping point for both battery life and thermal management.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

The first to put a 46mm cylinder into mass production was Tesla, which soon applied it to the Model Y and Cybertruck off the Texas plant after their release in 2020.

However, due to the manufacturing process at that time, the large cylinder was not perfect in fast charging and heat dissipation. What really saved the large cylinder was actually a process called "full pole ear".

In the past, the cell had only one or two pole ears, and the electrons had to trudge horizontally on metal foils that were tens of centimeters long. Once the large current passes, the high impedance will quickly heat the cell, which is also the reason why the early large cylindrical batteries did not dare to touch the high-power fast charge.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

The omnipolar approach is to make the edges of the pole piece into a whole conductive end face, so that the electrons flow out directly along a very short path.

The above paragraph does not need to be read carefully. You only need to know that this structural adjustment has reduced the internal resistance of the cell by 80%, and the heat production of the cell during charging and discharging has been greatly reduced.

It is precisely because the heat production has dropped that the cell has a higher thermal safety upper limit. With this layer of assurance, engineers dare to introduce a more active electrochemical system internally.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

This is why BMW can directly apply more than 90% of the high nickel anode and silicon carbon anode on the sixth generation of batteries.

The specific capacity of the silicon material is extremely high, but it expands like a balloon when saturated with lithium ions. If the square shell battery uses a high proportion of silicon cathode, the shell is easily supported and deformed, resulting in lithium precipitation.

The cylindrical steel shell has a natural axisymmetric structure and a strong circumferential mechanical stiffness, which can evenly constrain the deformation of the silicon negative electrode during the charging and discharging process.

In order to accommodate different models, BMW has also prepared cylindrical batteries in two specifications: the 95mm-high 4695 for the sedan, which reduces the chassis thickness; and the 120mm-high 46120 for the SUV, which increases the battery capacity.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

BMW did not engage in aggressive self-development and self-production like Tesla, but set its own recipe standards, and the production was left to Chinese suppliers - Ningde Times and Yiwei Lithium Energy.

It is precisely because of the mature manufacturing system that the 10 billion yuan battery project of the Shenyang factory was able to quickly land, and the hardware reserve was completed before the new generation was fully rolled out.

I don't know if you have encountered such a situation. As soon as the car speed reaches 120km/h, the air conditioner will not cool down any time soon. My Tesla Model 3 is like this, you have to manually lower the air conditioner two degrees each time, so that the car can be slightly cooler.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

This is actually the high temperature protection of the battery. According to the wind resistance and roll resistance data of Model 3, the battery needs to maintain a continuous output of 18 to 20kW when the vehicle is cruising at 120km/h.

According to Joule's law, the heat generated by the conductor is proportional to the square of the current, and continuous high-power discharge will cause rapid heat accumulation inside the cell. The biased power battery is particularly selective about the operating temperature. Once the cell temperature is too high, the thermal management platform will give priority to the battery for heat dissipation.

The core component of Tesla's integrated thermal management platform is the eight-way valve. When the battery is overheated, the eight-way valve will switch the flow direction of the refrigerant and coolant, and most of the refrigeration output of the compressor will be directly pumped to the battery water cooling circuit by means of a plate heat exchanger.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

The maximum cooling power of the Model 3 compressor is also three or four kilowatts in total. After being intercepted by the battery for most of the time, the air conditioner is naturally not cool enough.

Big cylindrical batteries are just the answer.

Since the internal resistance of the battery cell is reduced by 80%, the joule heat generated during the discharge process will be greatly reduced, and the conventional water cooling cycle is sufficient to maintain the normal temperature, and it is no longer necessary to compete with the cockpit for cooling.

In addition to the problem of high-speed air conditioning, the rear sitting position is also a place where pure electric cars are troughed for a long time.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

Taking into account the liquid cold plate and the protective cover plate, the whole package thickness of traditional square shell batteries is generally around 140 mm. In order to accommodate this battery in the chassis, many car cockpit floors need to be lifted two or three centimeters, and rear passengers will not be comfortable sitting for a long time due to the lack of support in their thighs.

The reason why the square shell battery is so thick is because the battery itself is weak, and the battery pack must be interspersed with heavy beams and frames for physical protection.

The 46 series large cylindrical steel shell has a strong compression resistance and can be directly used as a chassis stress structure. When BMW integrated it into the body, the thickness of the battery pack was reduced by nearly 20 mm.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

The chassis has become thinner, and the car has finally found the stretchy sitting posture of a traditional fuel vehicle.

There is also a puzzle. Since the perceived advantages of large cylindrical batteries are remarkable, why have domestic power battery manufacturers not transformed? The key is still cost.

At present, the domestic market is dominated by lithium iron phosphate, accounting for nearly 70% of the loading share. After the square shell is made into CTP, the volume utilization of the battery pack can exceed 70%. The triangular gap that cannot be eliminated naturally exists between the cylindrical cells, and the space utilization rate is usually only about 60%. Making a cylinder of iron and lithium with limited energy density will waste the chassis volume.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

In another dimension, domestic power battery companies have built up hundreds of GWh of square shell production capacity in the past few years, pushing the cost of cell manufacturing to a level of 0.3 to 0.4 yuan per watt hour. Under the fierce market competition, it is difficult for companies to spend a lot of money to push back.

And even stronger than Tesla, it fell over the 4680 battery.

In order to achieve a cost reduction of 56%, Tesla chose the dead-knocking method cathode process. However, due to the brittle cracking of the pole pieces during the compaction process, the early yield stays between 70% and 80% for a long time, and it is difficult to reach the break-even point of more than 95% of the mature production line, so Cybertruck's production capacity climbing has been delayed for a long time.

BMW chose a more ingenious path, they avoided the immature dry process, relying on high-speed wet process to achieve mass production.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

This choice certainly comes at a cost. The wet process is inseparable from solvent coating and high-temperature baking production lines. The plant occupies a large area and consumes a large amount of electricity. Relying on the positive dry process to reduce manufacturing costs, BMW obviously cannot enjoy the theoretical dividends.

But the price of luxury brands is enough to absorb these expenses, and BMW now needs the certainty of the rhythm of mass production more than the pursuit of extreme cost reduction.

In another dimension, there are a large number of speed-free highways in Germany. Vehicles travel long distances at speeds of 160 km/h or more, and the discharge power tends to reach 40 to 50 kilowatts. The physical characteristics of low internal resistance and axial heat dissipation of large cylinders are more suitable for this high load condition.

Large battery + low power consumption! The BMW new generation i3 ran 1213 kilometers and consumed only 8.8 degrees of energy per 100 kilometers?

Nowadays, BMW's new car rhythm is significantly compacted after removing the engineering obstacles of the battery.

According to BMW's plan, by 2027, the Chinese market will usher in nearly 20 new cars with next-generation craftsmanship. In addition, BMW intends to increase the proportion of domestic models to more than 95% by 2030 and sell “Made in China” BMWs overseas.

In the past few years, people have always stared at the car and intelligent driving, but as the model and market continue to mature, the competition for pure electric models will eventually return to the simple places of the chassis, thermal management and energy consumption.

This article is from: https://www.ifanr.com/1684510 For copyright issues, please write to: 13951431913#139.com or submit a review on the right.

暂无评论,快来发表第一条评论吧!No comments yet. Be the first!

📮 需求咨询📮 Inquiry