本文来源:https://mp.weixin.qq.com/s/NU-jRQQf1588QNn4Hrit4Q
若有版权问题,请来信告知:13951431913#139.com 或在右方提交评论。
从当年海信A9上市,到如今海信A10到手,前后隔了1599天。
四年多的时间,海信A10墨水屏5G手机算是正式交卷了。
实际上海信在交卷A10之前,还交卷了Hi Reader 2026:海信Hi Reader 2026实测:1.7 万个“下次一定”,终究是海信错付了
8月28号首发当天我去抢海信A10,没想到备货只有400台。

带背屏的Ultra版没抢到,白色也无缘,最后入手的是一台海信A10 Pro执简版墨竹绿12+512G。(这个规格是3499元)
熬过漫长的等发货阶段,总算在9月26号收到了。
今天这篇,是针对纯墨水屏单机的评测。

海信A10的硬件做工没有问题,整体相当出色。
但平台优化维度,有不少基础工作要做。(尤其是高刷和自动清残影也就是下面这两个方向,正因为它们存在短板,你会看到海信A10在本次测试的多个场景里处处受限)
打算当主力机或副机用——直接上12+512G顶配,别为省几百块钱委屈自己买低配。
只想买来当纯墨水屏电纸书——不推荐,市面上明显有更便宜、更好的选择。
高通QCM6690、4nm工艺8核、安卓16开放平台。
Carta 1300墨水屏、6.13英寸、300PPI、256级灰阶、36级冷暖前光。
搭载元太T2000硬件TCON芯片。
4000mAh电池,18W有线快充、15W无线快充、NFC、红外遥控、5G全网通、WiFi 6。
单卡槽。
摄像头前置800W+后置4800W。
整机190g、厚度8.2mm。
大家对海信A10的期待并不止于一款手机形态的电纸书,更想弄清楚它究竟能不能扛起主力机的大旗。
所以阅读体验放在后面说,先看它作为手机能不能hold住各类使用场景。
海信A10发布会上的一些其它细节,看这篇:海信A10墨水屏手机发布:2799元起,首发备货400台,四年磨一剑磨出了什么
海信A10底部的麦克孔和卡槽取卡孔排在了同一条线上,距离特别近。
靠近充电口的那个才是卡槽取卡孔,千万别捅错了。

要是捅进麦克风孔,防尘网一破,麦克风大概率就报废了。
防呆外观是手机行业踩过坑之后的经验,要么挪到侧面,要么把孔开在卡槽盖板上。
A9的卡槽是安排在侧面的,不知道A10出于什么考虑挪到了底部,又没有加防呆设计。

(包装盒里小白盒中的说明书上其实有写,但很少有人会翻说明书)
排队等二手退货的朋友,到手之后拿灯照着检查一下麦克孔。
整体做工偏硬朗风格,按键扎实,没有松垮感。
中框采用金属材质,背板是类玻纤材料,质感在线。
唯独摄像头区域用的是亚克力塑料,和机身其他部位不在一个档次,略显违和。(亚克力堪称指纹收集器,玻纤背板也容易刮出划痕,日常使用要多留意)

墨竹绿这个颜色绿中偏灰,女生建议直接入白色。
两个直角边做了圆角处理,比海信A9的45度斜切舒服不少,手感进步显著。
190g、8.2mm,作为主力手机,单手握持毫无压力。
NFC与红外遥控一个不缺,刷公交卡、遥控空调电视都没问题,是副机的加分项。
安兔兔V12.0.1实测跑分大约在73万到74万之间。
目前测不到GPU跑分,总分只是CPU、内存、UX三项叠加。CPU单核约32万左右,QCM6690差不多就是这个水平。

海信A10内置元太T2000硬件TCON芯片,专职负责墨水屏的刷新波形控制,把这份活儿从CPU手里接了过来,专芯专用。实际操作下来,跟手感比预期好。
至于高刷,海信官方没有公布具体帧率数据。
我打开开发者模式想测,跑帧软件无法识别这台设备,只能作罢。
连接同一个WiFi,海信A10下载APP眨眼就装完了。
同样的网络条件下,海信A9还在慢吞吞地爬进度条,海信A10已经装好投入使用了。
5G与WiFi 6的加持效果确实立竿见影。
老粉都清楚,我测高性能设备有个固定环节——压力三件套:番茄小说、哔哩哔哩、王者荣耀。
海信A10既然想当主力机,那就一视同仁,全部过一遍。
打开和加载速度都没问题,但翻页残影偏重,不手动全刷根本消不掉。
连续翻上几页,屏幕上就叠了好几层残影。

视频播放流畅度没问题,拖动进度条也跟得上。
只是清晰度有所牺牲,流畅和极速模式下画面偏糊。能看,但别对画质抱期望。

游戏能进,也能跑起来,说明性能上限是够用的。

这三件套都能顺利跑下来的话,高德地图、小红书、美团、淘宝、支付宝等第三方APP更是轻松拿捏。

墨水屏没有色彩,所有信息只能靠黑白深浅来区分。
灰阶就是墨水屏的"色准",这一项没调好,所有与显示相关的体验都会打折扣。
海信A10标称256级灰阶,硬件规格是到位的。
可实际的灰阶过渡只能算中规中矩。
以《七龙珠》那张画面为例,暗部压不下去,亮部与暗部之间的层次也拉不开。

高刷优化欠佳、自动清残影没做好、灰阶过渡不够细腻,三个问题叠在一起,整体显示效果就很吃亏。

甚至文字显示层面的问题,换任何字体都救不回来,这是系统层面的优化问题。
硬件发了一手好牌,可惜打牌的人还没坐上桌。
自动清残影是目前最大的短板。
各种模式下切换页面时,上一页的残留痕迹都挺明显,不会自动消除,只能靠手动全刷。
阅读体验是用微信读书墨水屏版测的。
清晰模式下字体没有锯齿,但翻页刷新那一下闪得比较晃眼。

均衡模式下闪烁改善明显,但字体边缘锯齿突出。

我再拉近景给大家看一下。
清晰模式下:

均衡模式下:

两个模式无法两全,要么清晰但闪屏,要么平滑但发糊。
海信A10的前光表现,是最让我意外的,可以说是我今年经手的几十台墨水屏设备里面,前光表现最均匀的一台。

再说,老粉都知道,我做前光测试向来直接拉满极值。极值状态下都这么出色,日常使用那还不得起飞咯。
原本对比测试要留到后面几篇文章,不过今天先放一张图出来,大家先感受一下。(图中4台机器,冷光、暖光数值全部拉到极值)

海信A10的充电标称18W,体感并不快。(注意注意,18W在墨水屏领域真的算快充,目前支持快充的墨水屏设备,这几个品牌加起来不超过10台)
4000mAh的电池当手机用,充电还是得等。
实测待机功耗:充满电静置9.5小时(晚12点到早9点半),不挂后台、只插一张电话卡,掉电17%。
同一晚A9掉电4%、大我HiBreak Pro掉电9%左右。
待机功耗目前来看略偏高,后续需要更长时间、更多机子来验证。
当主力机高频使用,一天一充是免不了的。纯阅读不折腾的话,撑两三天没问题。
海信A10的安卓16,平台运行格外稳定,这两天没有出现过假死或卡死。
APP兼容性没有问题,墨水屏版和原生版都能正常安装。
原生兼容通话录音,应用分身覆盖主流应用。

但要胜任主力机,系统细节的打磨还有大量工作要做。
你例如:
1、没有自带天气APP。桌面有天气显示,但应用列表里找不到独立的天气应用,只能下载第三方替代。
2、没有系统自带的换机助手。想把旧手机资料迁移过来,只能借助第三方工具。
3、验证码无法自动填充。如今主流手机都能自动识别并填入短信验证码,海信A10不具备这项能力。
4、不支持更换字体。目前只有字体大小和粗细可以调。
还有一些细节层面的缺失,就不逐一列举了。
这些都不算技术难题,却都是高频使用的细节。
一台3499块的手机,这些基本功不应该缺。
四年磨一剑,剑是磨出来了,剑鞘还没配齐。就看后续系统细节优化了。
通话是海信的老本行,完全没有问题。
拍照方面,墨水屏手机在手机端显示都是黑白的,效果取决于灰阶调校。

摄像头核心用途还是偏办公——扫文档、扫码之类。偶尔应急可以,别指望当主力。
还有个从海信A9就有的老毛病:音量键做在了电源键上面,想用音量键翻页手得往上挪,比较费劲。

海信A10 Ultra版那块4.96英寸LCD磁吸背屏,我没能买到。
但凭经验说一句:那块背屏多半只是个玩具。指望靠背屏扛起主力机场景,不够用。或者说,很多人实际用起来会嫌麻烦。(切换时每多一步,都会让人心生退意)
像海信A6L那样一体化双屏、翻个身即可切换,才是更合理的形态。
外挂式磁吸背屏走到哪都得多带一块,是负担而非补充。
希望海信下一代能另开一条线,做一款A6L式的一体化双屏手机。那才是笔者更想看到的完全体。
对咯,已经拿到背屏的小伙伴,告诉我背屏单独称重多少克?套上海信配的那个壳子后整体重量又是多少克?
Ultra每档比Pro贵400元左右,多出来的就是那块LCD背屏。
1、双机党。主力机是iPhone或安卓旗舰的话,配海信A10当副机完全够用。买Pro版即可,背屏对副机不是刚需。
2、想当唯一主力机的。 可以应付,前提是接受单卡,日常使用场景简单——接打电话、回微信、刷小红书、日常支付、偶尔办公之类。
3、海信死忠粉。 A10是海信墨水屏手机里性能和完成度最高的一款。没必要再留恋老型号了。
4、眼睛比较敏感的。A10的前光表现相当出色,如果你有眼疾之类的问题,可以买回去试试,没准真能缓解。
之前写海信Hi Reader 2026时:等了三年,海信墨水屏终于“现货”开售:这定价绝了
我在那篇文章结尾问过大家一句:“下次一定,还是这次一定?”
海信A10又把这道题带回来了。
这次——你们是下次一定,还是这次一定?
那啥,海信A10算是测完了,等后期不用预约、有现货的时候,我再把A10 Ultra白色版买回来。
当然,你们更想看的,估计是海信A10和大我HiBreak Pro的比较,安排。
以及海信A10和海信A9的比较,也安排。
甚至还想看海信A10、海信A9、海信Hi Reader 2026的比较,安排安排!

这几篇安排完,欢度国庆!
最后,附上5篇深度专栏文章:
👉3条斩杀线,终结墨水屏设备“买了又买”的内耗
👉墨水屏新手别乱买!一次讲透基础常识,省下上千元试错成本
👉书没读几本,墨水屏买了一堆|戒掉心瘾的12条纪律
👉巨头围剿下,墨水屏创业仅剩的3条路
👉二手墨水屏避坑指南:3次翻车换来的7条教训
From the launch of the Hisense A9 back then to the Hisense A10 finally arriving, 1599 days have passed in between.
Over four years of time, the Hisense A10 E-ink 5G phone can be said to have officially submitted its answer.
Actually, before submitting the A10, Hisense also released the Hi Reader 2026: Hisense Hi Reader 2026 Hands-On Review: 17,000 "next time for sure," in the end, Hisense's expectations were misplaced.
On August 28, the launch day, I went to grab the Hisense A10, only to find that the initial stock was just 400 units.
I couldn't get the Ultra version with a back screen, nor could I get the white one. Ultimately, I ended up with a Hisense A10 Pro Zhijian Edition in Ink Bamboo Green with 12GB + 512GB storage. (This configuration is priced at 3,499 yuan.)
After enduring the long wait for shipment, I finally received it on September 26.
This article today is a review focused on the pure E-ink standalone device.
PART 01
Let's start with the conclusion.
The hardware build quality of the Hisense A10 is not an issue; overall, it is quite excellent.
However, in terms of platform optimization, there is a lot of basic work to be done. (Especially in high refresh rates and automatic ghosting clearing, which are the two directions mentioned below. Because of these shortcomings, you will see the Hisense A10 severely limited in multiple scenarios in this test.)
If you plan to use it as a primary or secondary phone, go straight for the top-spec 12+512GB configuration. Do not compromise by buying the lower spec just to save a few hundred yuan.
If you just want to buy it as a pure E-ink e-reader, it is not recommended. There are clearly cheaper and better options on the market.
PART 02
Core Parameters at a Glance
Qualcomm QCM6690, 4nm process 8-core, Android 16 open platform.
Carta 1300 E-ink screen, 6.13 inches, 300 PPI, 256-level grayscale, 36-level warm/cool front light.
Equipped with the E Ink T2000 hardware TCON chip.
4000mAh battery, 18W wired fast charging, 15W wireless fast charging, NFC, infrared remote control, 5G full network, WiFi 6.
Single SIM card slot.
Camera: 8MP front + 48MP rear.
Total weight 190g, thickness 8.2mm.
Everyone's expectation of the Hisense A10 goes beyond just an e-reader in phone form; they want to know if it can truly serve as a primary phone.
So I will discuss the reading experience later. First, let's see if it can handle various usage scenarios as a phone.
For other details from the Hisense A10 launch event, read this: Hisense A10 E-ink Phone Launched: Starts at 2,799 yuan, Initial stock of 400 units, What did four years of polishing produce?
PART 03
Unboxing Tip: Don't Puncture the Wrong Hole
On the bottom of the Hisense A10, the microphone hole and the SIM tray ejector hole are aligned on the same line, very close together.
The one near the charging port is the SIM tray ejector hole. Do not puncture the wrong one.
If you puncture the microphone hole, the dust mesh will break, and the microphone will likely be ruined.
Fool-proof design is an experience learned from pitfalls in the phone industry. You should either move it to the side or place the hole on the SIM tray cover plate.
The A9's SIM slot was arranged on the side. It is unclear why the A10 moved it to the bottom without adding a fool-proof design.
(Actually, the manual in the small white box inside the packaging does state this, but few people read the manual.)
Friends waiting in line for second-hand returns, please inspect the microphone hole with a light after receiving the device.
PART 04
Build Quality and Appearance
The overall build style is sturdy. The buttons are solid and do not feel loose.
The middle frame is made of metal, and the back panel is a glass-fiber-like material with excellent texture.
The only downside is that the camera area uses acrylic plastic, which is not on the same level as the rest of the body and feels slightly out of place. (Acrylic is practically a fingerprint magnet, and the glass-fiber back panel is prone to scratches. Be careful during daily use.)
The Ink Bamboo Green color is a greyish green. Girls are advised to go for the white version directly.
The two sharp edges have rounded corners, which is much more comfortable than the 45-degree cut of the Hisense A9. There is a significant improvement in hand feel.
190g and 8.2mm. As a primary phone, holding it with one hand is effortless.
It has both NFC and infrared remote control. Swiping transit cards or controlling ACs and TVs is no problem. It is a plus for a secondary phone.
PART 05
Performance Benchmarks and T2000 Chip
Antutu V12.0.1 measured benchmarks are approximately between 730,000 and 740,000.
Currently, GPU scores cannot be measured. The total score is just the sum of CPU, Memory, and UX. The CPU single-core is around 320,000. The QCM6690 is roughly at this level.
The Hisense A10 has a built-in E Ink T2000 hardware TCON chip, dedicated to controlling the E-ink screen refresh waveforms. It took over this task from the CPU, specializing the chip for its purpose. In actual operation, the responsiveness is better than expected.
As for the high refresh rate, Hisense officials have not released specific frame rate data.
I turned on developer mode to test, but the frame rate app could not recognize this device, so I had to give up.
PART 06
Download Speed is Visibly Faster
Connected to the same WiFi, the Hisense A10 finished installing an app in the blink of an eye.
Under the same network conditions, while the Hisense A9 was slowly crawling up the progress bar, the Hisense A10 had already finished installing and was ready for use.
The boost from 5G and WiFi 6 is indeed immediate.
PART 07
Pressure Trio Test
Old fans know that I have a fixed segment for testing high-performance devices—the "Pressure Trio": Fanqie Novels, Bilibili, and Honor of Kings.
Since the Hisense A10 wants to be a primary phone, let's treat it equally and run through all of them.
Fanqie Novels
Opening and loading speed are fine, but page turning ghosting is heavy. It does not disappear unless you manually refresh the whole screen.
After flipping through a few pages in succession, multiple layers of ghosting stack up on the screen.
Bilibili
Video playback smoothness is fine, and dragging the progress bar keeps up.
However, there is a sacrifice in clarity. In Smooth and Extreme modes, the image is blurry. It is watchable, but do not expect high picture quality.
Honor of Kings
The game can be entered and run, indicating that the performance ceiling is sufficient.
If these three items run smoothly, third-party apps like Amap, Xiaohongshu, Meituan, Taobao, and Alipay are even easier to handle.
PART 08
Poor Grayscale Calibration Hurts All Visuals
E-ink screens have no color; all information must be distinguished by black and white shades.
Grayscale is the "color accuracy" of E-ink screens. If this is not tuned well, all display-related experiences will be discounted.
The Hisense A10 is labeled with 256-level grayscale; the hardware specs are adequate.
However, the actual grayscale transitions are only average.
Taking a scene from "Dragon Ball" as an example, the shadows cannot be pushed deep enough, and the layers between highlights and shadows cannot be separated well.
Poor high refresh rate optimization, inadequate automatic ghosting clearing, and insufficient smoothness in grayscale transitions. These three issues combined make the overall display effect suffer greatly.
Even at the level of text display, changing any font cannot save it. This is a system-level optimization issue.
The hardware dealt a good hand, but unfortunately, the player has not yet taken a seat at the table.
PART 09
Ghosting and Reading Experience
Automatic ghosting clearing is currently the biggest shortcoming.
When switching pages in various modes, the residual traces of the previous page are quite noticeable. They do not clear automatically; you can only rely on manual full refreshes.
The reading experience was tested using the E-ink version of WeChat Read.
In Clarity mode, fonts have no jagged edges, but the flash during page refresh is quite glaring.
In Balanced mode, the flickering is significantly improved, but the jagged edges on fonts are prominent.
Let me zoom in for a closer look.
In Clarity mode:
In Balanced mode:
The two modes cannot satisfy both requirements. It is either clear but with screen flashing, or smooth but blurry.
PART 10
Front Light and Charging/Battery Life
The front light performance of the Hisense A10 is what surprised me the most. It can be said to have the most uniform front light performance among the dozens of E-ink devices I have handled this year.
Besides, old fans know that I always push front light tests to extreme limits. If it performs this well at extreme levels, it must perform exceptionally well in daily use.
The comparison test was originally planned for later articles, but I am releasing one image today for everyone to feel it first. (The image shows 4 machines, with cold and warm light values all set to extreme limits.)
The Hisense A10's charging is labeled at 18W, which does not feel fast. (Note: 18W is really considered fast charging in the E-ink field. Currently, fewer than 10 E-ink devices supporting fast charging exist across these brands combined.)
With a 4000mAh battery used as a phone, you still have to wait for charging.
Measured standby power consumption: Left idle for 9.5 hours with full charge (from 12 PM to 9:30 AM), no background apps, only a single SIM card, battery dropped by 17%.
On the same night, the A9 dropped by 4%, and the HiBreak Pro dropped by about 9%.
Standby power consumption appears slightly high for now. It needs verification with longer durations and more units.
When used as a primary phone with high frequency, charging once a day is unavoidable. For pure reading without tinkering, it can easily last two to three days.
PART 11
System Experience: Usable, but Far from Great
The Android 16 on the Hisense A10 is exceptionally stable. No freezes or hangs have occurred in the past two days.
There are no issues with app compatibility. Both E-ink versions and native versions install normally.
It natively supports call recording, and app dual/clone covers mainstream apps.
However, to serve as a primary phone, a lot of work is still needed to polish system details.
For example:
1. No built-in weather app. The desktop shows weather, but you cannot find a standalone weather app in the list; you can only download a third-party alternative.
2. No system-built-in phone transfer assistant. To migrate data from an old phone, you have to rely on third-party tools.
3. Verification codes cannot be auto-filled. Nowadays, mainstream phones can automatically recognize and fill in SMS verification codes. The Hisense A10 lacks this capability.
4. Does not support changing fonts. Currently, only font size and weight can be adjusted.
There are other missing details, which I will not list one by one.
These are not technical difficulties, but they are details used frequently.
For a phone costing 3,499 yuan, these basic functions should not be missing.
Four years to sharpen the sword. The sword is sharpened, but the scabbard is not yet complete. Let's see how the subsequent system detail optimization goes.
PART 12
Calls, Camera, and Volume Keys
Calls are Hisense's strong suit; there are absolutely no problems.
Regarding the camera, E-ink phones display everything in black and white on the device side. The effect depends on grayscale calibration.
The core use of the camera is more office-oriented—scanning documents, scanning QR codes, etc. It is fine for occasional emergencies, but do not expect it to be a primary camera.
There is also an old issue from the Hisense A9: the volume keys are located above the power key. To use the volume keys for page turning, your hand has to move up, which is inconvenient.
PART 13
Back Screen: Looking Forward to a Complete A6L-style Form
I was unable to buy the 4.96-inch LCD magnetic back screen of the Hisense A10 Ultra version.
But based on experience, I say this: that back screen is probably just a toy. Expecting the back screen to handle primary phone scenarios is not enough. Or rather, many people will find it troublesome to actually use. (Every extra step in switching will make people want to quit.)
Like the Hisense A6L, with an integrated dual-screen and the ability to switch by just flipping the device over, is a more reasonable form factor.
An external magnetic back screen means carrying an extra block everywhere you go. It is a burden, not a supplement.
I hope Hisense's next generation will open a new line, creating an A6L-style integrated dual-screen phone. That is the complete form I would prefer to see.
Oh right, for those who have already received the back screen, tell me how many grams the back screen weighs alone? And what is the total weight after attaching the case provided by Hisense?
PART 14
Pricing and Purchase Advice
Model
8+128G
8+256G
12+512G
A10 Pro Zhijian Edition
2,799 yuan
2,999 yuan
3,499 yuan
A10 Ultra Yuejian Edition
3,198 yuan
3,398 yuan
3,898 yuan
Each Ultra tier is about 400 yuan more expensive than the Pro, the difference being that LCD back screen.
1. Dual-phone users. If your primary phone is an iPhone or an Android flagship, pairing the Hisense A10 as a secondary phone is completely sufficient. Buy the Pro version; the back screen is not a necessity for a secondary phone.
2. Those who want it as their only primary phone. It can cope, provided you accept the single SIM slot and have simple daily usage scenarios—calls, replying to WeChat, browsing Xiaohongshu, daily payments, occasional office work, etc.
3. Hisense loyal fans. The A10 is the highest performance and most complete model among Hisense's E-ink phones. There is no need to linger on older models.
4. Those with sensitive eyes. The A10's front light performance is excellent. If you have eye problems, you can buy one to try. It might actually help relieve symptoms.
When I wrote about the Hisense Hi Reader 2026 before: Waited Three Years, Hisense E-ink Finally "In Stock" on Sale: This Pricing is Incredible
I asked everyone at the end of that article: "Next time for sure, or this time for sure?"
The Hisense A10 brings this question back again.
This time—are you choosing "next time for sure," or "this time for sure"?
Well, the Hisense A10 review is done. I will buy the A10 Ultra white version later when pre-orders are no longer required and there is stock.
Of course, what you all probably want to see more is the comparison between the Hisense A10 and the HiBreak Pro. That is arranged.
And the comparison between the Hisense A10 and the Hisense A9 is also arranged.
Even the comparison between the Hisense A10, Hisense A9, and Hisense Hi Reader 2026. Arranged!
After finishing these articles, happy National Day!
Finally, here are 5 in-depth column articles:
👉 3 Kill Lines to End the Internal Struggle of "Buying and Buying Again" E-ink Devices
👉 E-ink Novices, Don't Buy Randomly! A Thorough Explanation of Basic Common Sense to Save Over a Thousand Yuan in Trial and Error
👉 Didn't Read Many Books, But Bought a Lot of E-ink Devices | 12 Disciplines to Quit the Addiction
👉 Under the Siege of Giants, The Only 3 Paths Left for E-ink Startups
👉 Second-hand E-ink Pitfall Avoidance Guide: 7 Lessons Learned from 3 Failures