最近看到 BornHack 2026 的电子胸牌,名字叫 Cyber Ægg(蛋形徽章),硬件仓库放在 Codeberg。
Cyber Ægg不是普通会议电子胸牌。Hackaday 对这个项目的评价挺到位:很多电子胸牌活动结束后就吃灰,Cyber Ægg 的思路是活动结束后还能继续当桌面时钟、日历和 MeshCore 节点用。
这个板子外形是半个蛋,配 3D 打印外壳,有点电子宠物的味道。现场使用时,它可以跑 Tamagotchi 风格的虚拟宠物、活动日历、RFID token 游戏;回到家以后,它还能立在桌面上,当一个低功耗电子纸终端。
Badge.Team 官方文档:
https://badge.team/docs/badges/bornhack-2026/
硬件仓库(KiCAD格式,包括主控原理图,NFC原理图,LoRA原理图等):
https://codeberg.org/Ranzbak/bornhack2026-hardware
固件源码( Rust / Embassy):
https://codeberg.org/Ranzbak/bornhack-firmware-2026
硬件核心是 Nordic nRF52840,,Cortex-M4F,带 BLE,也带 NFC tag PHY。Cyber Ægg 没有再额外塞一个蓝牙芯片,BLE 直接用 nRF52840 自带射频;NFC 也是用 nRF52840 的 NFC tag 功能,PCB 上绕了一组线圈,官方文档里提到线圈大约 2.8uH,通过电容调到 13.56MHz,另外需要注意它只能做 tag,不能做 reader。
显示部分用的是 1.54 英寸三色电子纸,黑、白、红三色,分辨率 152 × 152,控制器是 SSD1675 / SSD1675B,走 SPI接口。户外场景来说,电子纸非常合适:太阳底下可读,保持画面不用耗电。BornHack 一周时间,官方目标也是一次电池充电撑完整个 camp。
通信部分比较有意思,板上单独放了 Semtech SX1262 做 LoRa,还是 SPI 接口。LoRa 匹配和 balun 参考 Semtech 应用笔记,天线部分参考 TI 的设计。软件网络侧则跑 MeshCore,这样它不只是一个本地小玩具,而是能加入营地 mesh 网络的节点。
主要器件大概如下:
模块 | 器件 / 方案 | 接口 |
MCU | Nordic nRF52840 | - |
显示 | 1.54 英寸三色电子纸,SSD1675/SSD1675B | SPI |
LoRa | Semtech SX1262 | SPI |
蓝牙 | nRF52840 内置 BLE | - |
NFC | nRF52840 NFC tag PHY + PCB 线圈 | - |
输入 | 五向摇杆、Execute、Cancel 按键 | GPIO |
反馈 | RGB LED、压电蜂鸣器 | GPIO / PWM |
电源 | 锂电池、USB-C、拨动开关 | - |
扩展 | QWIIC / I2C | I2C |
硬件是 KiCad 开源的,仓库里能看到主控、LoRa、显示、电源、NFC、QWIIC 等分模块原理图:
这里有个小坑,官方文档也直接写出来了:板上的 QWIIC 接口把 3.3V 和 GND 交换了。也就是说,不能拿普通 QWIIC 线直接插外设,要做一根修正线,把电源两根线在一端交叉。官方还提醒,一些 NFC、LoRa、Bluetooth 射频电路还留着 U.FL / IPEX 连接器,主要是方便调试和天线匹配,PCB 天线还没有完整表征,不建议现在直接打板量产。
把活动纪念品做成一个长期可用的低功耗设备,这是项目最大亮点,nRF52840 负责 BLE、NFC 和主控,SX1262 负责远距离 mesh,电子纸负责常显界面,五向摇杆和两个按键负责本地交互,USB-C 负责供电和数据,锂电池负责离线运行。东西不复杂,但组合得很完整。
关注公众号“嵌入式杂谈”,了解更多有趣好玩的嵌入式信息,感谢大家的点赞,在看。
Recently saw the BornHack 2026 electronic badge, named Cyber Ægg (egg-shaped badge), hardware repo on Codeberg.
Cyber Ægg is not an ordinary conference electronic badge. Hackaday's review is quite apt: many electronic badges end up gathering dust after the event, while Cyber Ægg's idea is that after the event it can continue as a desktop clock, calendar, and MeshCore node.
The board is shaped like half an egg, with a 3D printed shell, somewhat like a digital pet. At the event, it can run Tamagotchi-style virtual pets, an event calendar, and RFID token games; back home, it can stand on the desk as a low-power e-paper terminal.
Badge.Team official docs:
https://badge.team/docs/badges/bornhack-2026/
Hardware repo (KiCad format, includes main MCU schematic, NFC schematic, LoRa schematic etc.):
https://codeberg.org/Ranzbak/bornhack2026-hardware
Firmware source (Rust / Embassy):
https://codeberg.org/Ranzbak/bornhack-firmware-2026
The hardware core is Nordic nRF52840, Cortex-M4F, with BLE and NFC tag PHY. Cyber Ægg does not add an extra Bluetooth chip; BLE uses nRF52840's built-in radio directly. NFC also uses nRF52840's NFC tag function, with a coil wound on the PCB. The official docs mention the coil is about 2.8uH, tuned to 13.56MHz with capacitors. Also note it can only act as a tag, not a reader.
The display uses a 1.54-inch three-color e-paper in black, white, and red, resolution 152×152, controller SSD1675 / SSD1675B, SPI interface. For outdoor scenarios, e-paper is very suitable: readable in sunlight, and holding the image consumes no power. BornHack lasts a week, and the official target is one battery charge lasting the whole camp.
The communication part is interesting: the board has a separate Semtech SX1262 for LoRa, also on SPI. LoRa matching and balun reference Semtech's application note, and the antenna part references TI's design. On the software network side it runs MeshCore, so it is not just a local toy but a node that can join the camp mesh network.
Main components roughly as follows:
Module
Component / Solution
Interface
MCU
Nordic nRF52840
-
Display
1.54-inch three-color e-paper, SSD1675/SSD1675B
SPI
LoRa
Semtech SX1262
SPI
Bluetooth
nRF52840 built-in BLE
-
NFC
nRF52840 NFC tag PHY + PCB coil
-
Input
Five-way joystick, Execute, Cancel buttons
GPIO
Feedback
RGB LED, piezoelectric buzzer
GPIO / PWM
Power
Lithium battery, USB-C, toggle switch
-
Expansion
QWIIC / I2C
I2C
The hardware is open source in KiCad; the repo contains separate module schematics for main MCU, LoRa, display, power, NFC, QWIIC, etc.:
There is a small pitfall, also directly documented in the official docs: the QWIIC connector on the board swaps 3.3V and GND. That means you cannot plug ordinary QWIIC cables directly into peripherals; you need to make a correction cable that crosses the two power wires at one end. The officials also remind that some NFC, LoRa, and Bluetooth RF circuits still have U.FL / IPEX connectors, mainly for debugging and antenna matching; the PCB antenna has not been fully characterized, so it is not recommended to go directly to PCB fab for mass production now.
Making an event souvenir into a long-term usable low-power device is the biggest highlight of the project. The nRF52840 handles BLE, NFC, and main control; the SX1262 handles long-range mesh; the e-paper handles the always-on display; the five-way joystick and two buttons handle local interaction; USB-C handles power and data; and the lithium battery handles offline operation. The thing is not complicated, but the combination is very complete.
Follow the official account "嵌入式杂谈" for more interesting and fun embedded information. Thanks for your likes and shares.